CIGABUY DNA40 temp control chip £25-50 ish shipped

[robby]

www.cigabuy.com/dna-40-40w-box-mod-chip-with-temperature-control-p-6978.html

Includes Registered slow boat (about £5-50)

[decoy]

ordered for to try and fit in mini clouper
temp control mod for £40 i likes it lol

[robby]

Jan 30, 2015 2:43:53 GMT decoy said:

ordered for to try and fit in mini clouper
temp control mod for £40 i likes it lol

The shipping is a bugger

[decoy]

i could of got it as lo as 56 p but went for the fast reg that was $5.80 which isnt that much really lol
i gota find some switches fast ish any idears

[robby]

Never really sourced them decoy, I think VapingBad has though Bed time , night

[robby]

Kerchinged one as well decoy along with some Hangsen Virginia Essence flavouring. Havent got a home for it yet though

[decoy]

looked up some buttons
www.modmaker.co.uk/Blue-LED-Momentary-Tactile-Switch are a bout the best looking buttons ive found that might work but unsure if they can be wired to light up with this without causing probs


im sorry but these just dont float my boat www.modmaker.co.uk/Mod-Making-Supplies/Switches/Tactile-Switches/Silver-Spherical-Actuator-Tactile-Switch
or can these be used with the original switch tops www.modmaker.co.uk/Mod-Making-Supplies/Switches/Tactile-Switches/Tactile-Push-Button-Momentary-Switch-4-Pin-12-x-12%20x-4.3mm

sorry for using the same web sight but it was the 1st to come up with the fat daddys v3 510(15mm) as mine has a little wobble on

oh its going in a mini cluoper just saying for those that dont know

[robby]

www.modmaker.co.uk/How-to-Wire-an-illuminated-switch-when-pressed

Shouldn`t cause any problems decoy but it depends where you wire it to. The way they have wired in their diagram would be fine for a mech mod, but for a regulated mod you would be better wiring it to the battery because of the variable output of the board The resistor value would probably need to be calculated, but not a problem. The switch that fires the LED is totally independant of the board circuitry. Think of it as two independant switches that are fired when you push one button  You could simply wire it to the plus and minus of the battery. You will need to buy a resistor for a couple of pence.






Looks like a 150 ohm 1/8th Watt resistor will be fine.

[decoy]

cheers for that robby wasnt sure if it had separate power supply for the led
looks like its going to be pimp my mod
the fat daddy is going to be a v tight fit the nut defo wont fit so ive got to find my tap and die set gerr
also got a tin of black and silver hammerite because i might as well paint it with something that might stand up to my rough love(if it works lol)
and have had a baoldrick moement with the batt door rattle
dont think im gong to use the temp control thingy ma bob but yer never know

[robby]

I dont know what I`m gonna do with mine, I have an unused basic wooden box mod which might fit the bill though

[decoy]

it came on sat but i missed the delivery
lights up with hana mods which is a bit strange
looks like im going to have to use diff tactile switches which is a bit of a bummer but hay ho

[robby]

Got mine as well, no idea what to put it in yet though decoy

[decoy]

Do not put this chip in anything biggest bag of shyt ever
Had it all wired up to check it worked before fitting it and soldered it all up,checked all was fine and it was so went to make a coffie
came back and 8ts melted the cover off my batt
all joints were good and it wasnt near anything that could of shorted it
i might have one last go with this sodding mini clouper but its going to be an evolve chip if i do
not hp at all

[robby]

sheet