Any Non Leaking RTA's out there,

[mowjo]

Ok I'm looking for a Cheapish RTA that dosn't leak, I have a couple of Orchid V6's but no matter how I wick them they leak like seives and it's getting on my nerves, I can't fault the Vapour or Flavour but I've tried every way on Youtube for Orchids and Billows, one did last a day then dumped a tank on me, so I'm now looking for something that has a single coil and dosn't leak, I like the look of the Russian 91% from FT and have heard good things about it,so far the only problem I can find with the Russian is the centre pin connector could be a problem if you don't set it up right, any recommendations for a leak free tank anyone??

Mow,,,

[phtumshk]

FT kayfun for cheap.
Lemo for a bit more.
Ive had a few incontinent Kfuns though, but fine once there set right.

Will add FT erlkonigins to that list, there easier than the K funs to set up.
ERLKONKING

[reddragon]

I have two kayfun lite + and whilst I love them I wouldn't say they are leak free. However, I have two lemo drops and one lemo and have not lost a drop from any of them, so that is what I would recommend.

[Q]

Well I've got 2 of Arrons Rose v2 clones, 1 from Focalecig, and 1 I've made from bits and none of them have EVER leaked, I wick them profusely and touch wood they behave themselves

[Get Off My Cloud]

Lemo/Lemo Drop
Subtank/Subtank Mini

[autumntwist32]

My Lemo Drop has never leaked

[Montana]

+1 for the Subtank Mini or the Subtank Nano.

I know the Nano isn't a rebuildable but I find the taste to better than the Mini and building the stock coils is very , very easy.



Andy

[lisburnvapes]

Kayfun lite v2 all the way,
Cheap (ft 1:1 clone)
Easy build
Adjustable airflow
Good flavour
Good vapour
What more could you want !

[Greg]

For me the Subtank mini is the only atty ive had that has never leaked at all. Plenty of others that don't leak often but the ST never leaks in my experience. And it's one of the cheapest too, especially for a genuine.

[300]

These don't leak.....
Kayfunator
Prometey II
Troy X
Troy X Mini
Rose V1
Spheroid
Heron
Penelope V3

Maybe not cheapish but i don't buy very often & i reckon most peeps here have prolly spent more on clearos / clones in the time it took me to collect these.

Heron clone performs just as well as the original if you drill out the bell to 3mm, only £12ish & it refuses to leak.

[mowjo]

Thanks folk I'm checking them all out, so it's back to my old Protank 2's for now, finaly stopped the leak onto the centre pin, I just wish I could get the same flavour from it as the Orchid,,,

[decoy]

its funny most rta,s leek to some degree
my kfl do and one of my erl clones leeks like a pig unless i do it just so the 1st erl clone that fast tech have stopped doing has never leaked(smaller juice channels)
the rose is prob the only atty ive had that hasnt leaked ever but its such a faff to set it up to get a good vape out of it its now unused
i think its all down to how you wick the little suckkers and the tank having an air tight seal
havent used a sub tank but as you can see they are well liked im going to take a punt on the ud goblin when they become more freely available,will it leak prob but it looks easy to set up for sub ohm dripping type tank

have you messed about with how much cotton your stuffing in the juice channels on the orchids(it was a faff getting the v 5 fogger not to leek but now with the right amount of cotton in the channels it works like a champ and no leeks and it looks the same as the orchids)

i know that not to helpfull but i think this is why some peps love and atty and some hate it ,it just down to wicking it right and the lovers have sussed it by luck of judgement

just on a side note when i gets a new atty ill buy some cheep shyt juice (pound shop)to learn to set it up and leave it in a bowl over night to see how much leaks out lol

[b1mble]

Aqua - never leaked on me but a small tank and a bit of a pain to build
Aqua V2 - never leaks, much easier to build
Rose v2 clones - never leaked. Can take huge coils and wick with stupid builds
Neither of my Erlkoenigin clones have leaked, but they don't much care for the power levels I prefer. It'll spit boiling juice at you at 30W
None of my Foggers (4.4, 4.4, 5, Big Fogger) widdle. The big Fogger is a monster pain in the rear to build though - it is way worse than pigs like the Ithaka.
I've just got some new post screws (M1.6x3mm) with flatter bases that I hope will make Fogger 4.4 building less of a pain. The stock screws spit the wires back out every time.

[sydsut]

Maybe I'm just lucky but neither of my Orchid V4 and V3 clones leak. Orchid V4 only leaked on the first build I did but once I sussed out the tiny tail just poking into the juice channel all has been fine. V3 has never leaked. It also occurs to me that I always use Celucotton rayon so maybe its the cotton that's causing the problems some are experiencing.

[lairey]

Another vote for the Lemo/Lemo Drops... I have 3 of them and all 3 are in daily use... never leaked and so simple to build... even better, they come with a 1.1 ohm coil already installed which lasts for ages with a little dry burn every time you re-wick