SS firmware upgrade and tool for X Cube 2.

[robby]

www.smoktech.com/hotnews/products/x-cube-two-firmware-upgrade-guide

SS coil upgrade.

7xjcc4.com2.z0.glb.qiniucdn.com/device/XCUBEII-Firmware-Tool(Beta).zip

A much simplified firmware upgrade tool Still in Beta.

[Deleted]

cheers for that robby

[Deleted]

Have you tried SS coils?

Offices up and down the country will end up running out of paper clips

[robby]

No I haven`t yet kreed

[Deleted]

I upgraded to it last night and the damn TC issues reared its ugly head again! The new upgrade tool would not work with mine, so I reverted to the old version. I am guessing there are either different boards or chips in these as some seem to work well, where the likes of Qand I have similar issues.

In fact I have decided to bin TC on this mod, it's just not worth the hassle so the plan is just going to be using Watrage mode and the TFV4

[Deleted]

Oh I did remember to change the Coefficient again for Ni, as again at 0.00600 barely a whisper

[robby]

Make sure you keep the fire button thingy pressed ALL the way through the process with no batteries in and no atty connected car147 with either upgrade tool. Sorry it aint working for you, really pleased with mine.

[robby]

Sept 3, 2015 11:07:26 GMT car147 said:

Oh I did remember to change the Coefficient again for Ni, as again at 0.00600 barely a whisper

Is it set at .00641 now car147, dont know how much difference it makes but that`s where I assume that should be, could be wrong though.

[Deleted]

Yeah I did m8 even following the tutorial on their website to make sure. There is some issue with mine, I cannot put a finger on it, but there's something just not right in Temp mode.

At first I thought it was my Subtank attys, but all of them? And stranger still they work fine on my Rdba40, Sigelie and TC Clones.

Quite happy to just us it in Watt mode, and use the others for TC

[Deleted]

I had to raise it to 0.00680 to get anything like a decent bit of puff. And over 500f

[robby]

Put it up some more and turn the temp down until it seems right. I never get hung up on numbers on these things, they are all a bit different, but with TC, even .02 ohms on the resistance can make all the difference. Yes, I know it isn`t ideal but I tend to be pragmatic about these things

[VapingBad]

Sept 3, 2015 11:17:04 GMT car147 said:

I had to raise it to 0.00680 to get anything like a decent bit of puff. And over 500f

If it has an internal resistance offset or adjustment that may help, any significant IR it could be that throwing it off especially vaping at the lower end of the ohm range, if so try 0.01 or 0.02 at first and tune it until it vapes like the others with the TCR at 0.0064.

[Deleted]

I am not too bothered robby, as it's fine with Kanthal, just cannot be arsed to jump through hoops getting it replaced, and to be fair it's the first real issue I have had with a Chinese purchase.

[Deleted]

Sept 3, 2015 11:26:13 GMT VapingBad said:

Sept 3, 2015 11:17:04 GMT car147 said:

I had to raise it to 0.00680 to get anything like a decent bit of puff. And over 500f

If it has an internal resistance offset or adjustment that may help, any significant IR it could be that throwing it off especially vaping at the lower end of the ohm range, if so try 0.01 or 0.02 at first and tune it until it vapes like the others with the TCR at 0.0064.

You may be onto something there mate

cheers

[robby]

I`m not sure I believe their reasoning for adding it, but as stated earlier it can make all the difference