intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 21, 2014 16:40:38 GMT
Hi i have a nemesis clone and it seems to have a diffrent pin on it to the hcigar one i had a while back and now it wont fit the kick 2 i have bought - basically when i fit it in the tubes screw back together but not all the way hence making the tubes wobbly - any idea's how i can overcome this of maybe i should just get another hcigar one ?
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 20, 2014 14:06:05 GMT
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 19, 2014 17:20:11 GMT
I just did 11 wraps on 25 kanthal around a 2mm drill bit and im getting 2.65 ohm
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 19, 2014 12:36:47 GMT
Thanks everyone for your appreciated advice
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 19, 2014 12:33:37 GMT
is it not ok to have 1.3/4 ohm builds then as they seem to vaping ok ?
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 19, 2014 12:31:11 GMT
I'd say there was something wrong if 6 wraps gives you a range of 1.3 - 4.0 ohms. I use 0.2 kanthal, 10 wraps on a 1.5mm drill bit gives me around 2 ohms consistently. There are some good guides on here, and a ton of vids on youtube... my suggestion is to watch a few vids, get a few different gauges of Kanthal, and practice, practice, practice... it takes a while to get consistent with your coils. But the effort is worth it. Good luck. when i wrap them i dont do micro coil i just do normal wraps - is this wrong ?
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 19, 2014 11:08:28 GMT
Hi at moment im using 0.25 kanthal and was wondering if i should use a different gauge to get better results - i normally wrap 6 wraps with cotton and get 1.3 to 4 ohm ?
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 17, 2014 20:31:30 GMT
I think the pin stops the bottom from spinning round
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 17, 2014 20:30:33 GMT
I have a Nemesis. I also have 5 pairs of magnets. The two have not met yet, as it's clear that using the magnets would require removing (permanently) the tiny "pin"... as I don't know what purpose the "pin" serves, I am not even going to try. Works for me. I'm lazy at this sort of stuff. I thought the pin has to be put back on ?
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 17, 2014 12:19:48 GMT
Only if the threading matched mate i just took that white plastic bit off the bottom and it still works so im hoping the magnets will thanks for your comments
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 17, 2014 11:52:37 GMT
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 17, 2014 11:22:26 GMT
It does indeed look different, It's hard to tell from the pic whether or not the magnets will fit. Where did you get the mod from? I bought it from somebody on a forum - it looks the same as the ones i have seen online just a different colour
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 17, 2014 10:51:44 GMT
Hi i bought a nemesis clone which i think is a bit of a cheap one and was just wondering if the magnet kit you can get will fit on this fire button as it looks different to some i have seen online ?
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 16, 2014 23:01:57 GMT
Why not get yourself a kick to put in your mech. Set it to the wattage you like to vape at. It will give you a consistent vape until the battery gets to low and then cut the power. No worring about over discharing the battery. yes i was looking at those - think i will thanks
|
|
intheblim
Full Member
Joined:April 2014
Posts: 135
Location:
Likes: 31
Recent Posts
Last Online Sept 17, 2014 19:12:02 GMT
|
Post by intheblim on Jun 16, 2014 20:45:18 GMT
so many understanding helpful people on this forum once again many thanks
|
|