Jerri
Super Member
Joined:October 2012
Posts: 2,321
Location:
Likes: 951
Recent Posts
Last Online Mar 23, 2024 23:18:41 GMT
|
Post by Jerri on Dec 12, 2012 15:34:24 GMT
I have several mini nova's, for some reason they keep bubbling and leaking from the top.
I'm using one now, worked perfectly all day yesterday, just topped it up (used a needle top with the nova slanted) and now it's bubbling and leaking from the top.
Am I filling it wrong?
It's really starting to get on my nerves now.
And advice greatly appreciated.
Thanks
|
|
steve386
VENDOR
Joined:July 2011
Posts: 2,361
Location:
Likes: 87
Recent Posts
Last Online Sept 30, 2024 20:58:08 GMT
|
Post by steve386 on Dec 12, 2012 15:36:55 GMT
Are you screwing the tops back on fully? I had one do this and that was the reason. When I looked there was a small gap.
|
|
Jerri
Super Member
Joined:October 2012
Posts: 2,321
Location:
Likes: 951
Recent Posts
Last Online Mar 23, 2024 23:18:41 GMT
|
Post by Jerri on Dec 12, 2012 15:47:54 GMT
Thanks for the reply.
Yes, just checked, top is screwed on properly.
|
|
genguskhan
Super Member
Joined:September 2012
Posts: 797
Location:
Likes: 197
Recent Posts
Last Online Jun 16, 2016 5:20:46 GMT
|
Post by genguskhan on Dec 12, 2012 15:55:24 GMT
Have you checked that the wick head is screwed on tight? Maybe with unscrewing the top you've unscrewed the head abit which might allow air in to the juice? I've never had that one before? Just a thought
|
|
ChillerVapes
Super Member
Aka Chillerhippie
Joined:October 2012
Posts: 1,675
Location:
Likes: 470
Recent Posts
Last Online May 8, 2015 18:55:40 GMT
|
Post by ChillerVapes on Dec 12, 2012 16:02:23 GMT
Also make sure your not over filling them. Too much juice = not good. To tighten the head without emptying, unscrew the top cap, remove the rubber head and gently use a flat head screwdriver to tighten.
|
|
Jerri
Super Member
Joined:October 2012
Posts: 2,321
Location:
Likes: 951
Recent Posts
Last Online Mar 23, 2024 23:18:41 GMT
|
Post by Jerri on Dec 12, 2012 16:36:05 GMT
Thanks. Will give that a try.
|
|
suede
Senior Member
THE BELFASTBHOY
Joined:October 2012
Posts: 457
Location:
Likes: 92
Recent Posts
Last Online Nov 5, 2020 12:47:16 GMT
|
Post by suede on Dec 12, 2012 20:37:54 GMT
Make sure you push the drip tip right down. It's a snug fit.
|
|
vapee
Senior Member
Joined:July 2012
Posts: 461
Location:
Likes: 133
Recent Posts
Last Online Feb 15, 2013 4:42:42 GMT
|
Post by vapee on Dec 12, 2012 21:22:16 GMT
I usually keep em upright the whole time and dont fill above 2mls - if i fill above that amount-ish it can have a small leak at fist from the 510 connector end but its just an initial leak and goes away quick. Kinda makes it annoying to use though as its not as portable as i'd like but they give good vapour and flavour so has some good advantages Also I did notice as pointed out about when unscrewing, it can unscrew the head a bit, sometimes enough to stop the connection, guess that means its got a nice seal at the top.
|
|
booblay
Super Member
Joined:July 2012
Posts: 627
Location:
Likes: 46
Recent Posts
Last Online Jul 2, 2014 6:37:36 GMT
|
Post by booblay on Dec 12, 2012 21:24:27 GMT
I actually noticed recently that screwing the heads down too tight can result in gurglerama. It is a delicate balance, aint it?
|
|
Jerri
Super Member
Joined:October 2012
Posts: 2,321
Location:
Likes: 951
Recent Posts
Last Online Mar 23, 2024 23:18:41 GMT
|
Post by Jerri on Dec 12, 2012 22:32:36 GMT
Seems the head was too tight. I turned it half a turn and it stopped after a few vapes. Thanks
|
|
bomberharris
Super Member
stick your role ups
Joined:November 2012
Posts: 2,098
Location:
Likes: 494
Recent Posts
Last Online Nov 20, 2016 13:54:38 GMT
|
Post by bomberharris on Dec 12, 2012 22:36:36 GMT
what I normaly do is give the lid a good clean underneath as there some times is a small pool of fluid , might be just something simple like that.
|
|