Airflow control Phoenix,Vaporbreak, £7-30 shipped!!! SS

[robby]

Jun 14, 2013 11:43:15 GMT Pezz said:

Jun 14, 2013 9:52:28 GMT xtc263 said:

How do you take it apart?

Having pulled the top half of the atty off I'll admit to staring down into mine for five minutes wandering how the heck will I put a coil in there....

Then I realised that the bottom half also comes off ... See the picture above ... it is a tight fit so you will have to pull fairly hard.



That said I've found that it is a great little RDA and I'm happy to have two on the go at the moment.

A top recommendation from robby

Glad you like it, just be careful with the o rings, everything seems a bit tighter than I would like and I am getting a bit of wear on one of the O rings, put a little juice around them every time you put it back together xtc263 Pezz 

[richo71]

Jun 14, 2013 0:03:56 GMT lemental said:

Does anyone know the size of screws I can use to replace those fiddly hex screws that come with it and where I can get some?
Would much prefer philips screws.

I have replaced the grub screws with flat head M2 screws (electrical screws) did it this way to allow the coil to sit higher on the posts and to be inline with the airflow

[robby]

Jun 14, 2013 12:46:52 GMT richo71 said:

Jun 14, 2013 0:03:56 GMT lemental said:

Does anyone know the size of screws I can use to replace those fiddly hex screws that come with it and where I can get some?
Would much prefer philips screws.

I have replaced the grub screws with flat head M2 screws (electrical screws) did it this way to allow the coil to sit higher on the posts and to be inline with the airflow

Good info, so they are deffo M2 then richo71

[richo71]

Jun 14, 2013 12:49:00 GMT robby said:

Jun 14, 2013 12:46:52 GMT richo71 said:

I have replaced the grub screws with flat head M2 screws (electrical screws) did it this way to allow the coil to sit higher on the posts and to be inline with the airflow

Good info, so they are deffo M2 then richo71

Yeh robby, i was quite lucky in that i have a small screws n fasteners shop up the road and he sorted me out, he just said they were stainless steel electrical contact screws

[richo71]

Your not showing as online again robby

[robby]

Strange richo71, can you see ONLINE under my avatar? I see it ???

[richo71]

No, pro boards has been pants over the past week or so though

[robby]

Weird, I can see Member is Online under your avatar and mine, must check my settings

[Perpetua]

I can see you Robby.


Though I think something is amiss as this is the second lunchtime I've not bought something from VB or FT during my break.

[womble]

Something's going wrong with the things which shows when someone was last online as well. It tells me robby was last online on May22nd?

[lemental]

Jun 14, 2013 12:46:52 GMT richo71 said:

Jun 14, 2013 0:03:56 GMT lemental said:

Does anyone know the size of screws I can use to replace those fiddly hex screws that come with it and where I can get some?
Would much prefer philips screws.

I have replaced the grub screws with flat head M2 screws (electrical screws) did it this way to allow the coil to sit higher on the posts and to be inline with the airflow

Thanks  Will try and find some.

[Super-Shiny]

Jun 14, 2013 15:35:34 GMT womble said:

Something's going wrong with the things which shows when someone was last online as well. It tells me robby was last online on May22nd?

I think this happens where members who show offline in their profile when really they are online, glitch maybe.

22nd of May might of been the day he chose to appear offline and hide from us all

[fiddles]

Just thought has anyone double checked his Avatar ?
robby could be using some of that illegal subliminal advertising hidden in there

[punisher]

hey robby 2 of these just dropped through my door
ripped out the old coil added a 1.2ohm with more silica wick
dropped it on my vamo 1.2ohm (just fires keeps dropping out )
vapes like a steam train even on the ego well impressed
cant wait for monday and my mec mod
www.vaporbreak.com/231-829-large_default/airflow-control-stainless-steel-rebuildable-phoenix-v5-atomizer-for-dry-herb-and-e-liquid.jpg

[robby]

Jun 21, 2013 20:50:48 GMT punisher said:

hey robby 2 of these just dropped through my door
ripped out the old coil added a 1.2ohm with more silica wick
dropped it on my vamo 1.2ohm (just fires keeps dropping out )
vapes like a steam train even on the ego well impressed
cant wait for monday and my mec mod
www.vaporbreak.com/231-829-large_default/airflow-control-stainless-steel-rebuildable-phoenix-v5-atomizer-for-dry-herb-and-e-liquid.jpg

Nice one mate, watch those O rings, they seem a bit easily worn. The whole thing seems quite tight (on mine anyway). Crackin wee dripper though  punisher . I must try mine on the KTS. How`s things mate?