Squape Clone Flooding

[spikus]

I use cotton wool in my 2 Taifun clones ... Works great

[Dunny]

Apr 7, 2014 20:26:00 GMT fiddles said:

I have 3 kayfun clones & use microils & cotton in all 3, havent tried the taifun so cannot comment on that

Guess I'll have to look for some tutorials for the taifun then!
Thanks again for the advice

[Dunny]

Apr 7, 2014 20:28:00 GMT spikus said:

I use cotton wool in my 2 Taifun clones ... Works great

Do you know of any tutorials worth watching?

[fiddles]

Apr 7, 2014 20:28:31 GMT Dunny said:

Guess I'll have to look for some tutorials for the taifun then!
Thanks again for the advice

No problem you are most welcome

[spikus]

It's dead simple ... Usual micro coil .. And treat it the same as if using silica... I'll see if I have any pics

[Dunny]

Apr 7, 2014 20:35:28 GMT spikus said:

It's dead simple ... Usual micro coil .. And treat it the same as if using silica... I'll see if I have any pics

Pics would be great thanks

[spikus]

An attenpt at a dual coil ... Turned out rubbish .... And a 2 strand twisted 0.25 kanthal micro coil ... Still going strong 0.9 ohms ... Great vape ..

[spikus]

Whoops ... Ignore 2nd pic ... That's a Squape

[spikus]

Here's the twisted coil.. And a pic of how long to cut the cotton wool before screwing on the tank section

[Dunny]

Apr 7, 2014 20:55:10 GMT spikus said:

Here's the twisted coil.. And a pic of how long to cut the cotton wool before screwing on the tank section

Well it looks easy enough. I must ask what do you mean by twisted?

[spikus]

Instead of one length of kanthal you use two ... Doubled over ... Hold one end tight then put the other 2 ends in a drill chuck ... Then start the drill and twist the two lengths until it forms a braided length resembling a rope ... Then use that and coil as normal .... It gives the same effect as using dual coils ... I.e halves the resistance ... ... Zoom in on the coil posted and you will see

[richvapers]

Apr 5, 2014 9:05:49 GMT fiddles said:

Apr 5, 2014 8:47:57 GMT Dunny said:

fiddles what sort or setup do you use on your squape?

Microcoil & cotton
cotton is right down channels, no leaks or gurgles

i do the same as fiddles, dunny - cotton right down the channels, and not a leak in sight.
And must say? because of all the negative feedback from fasttech on this glass squape?
i gave the thing up before i even got it.
And have to say it is performing great for the time being.
Had to do the fix with the 510 pin that spikus put up.
But for the moment i am likeing it

[Dunny]

Apr 7, 2014 21:41:24 GMT richvapers said:

i do the same as fiddles, dunny - cotton right down the channels, and not a leak in sight.
And must say? because of all the negative feedback from fasttech on this glass squape?
i gave the thing up before i even got it.
And have to say it is performing great for the time being.
Had to do the fix with the 510 pin that spikus put up.
But for the moment i am likeing it

Yeah I followed fiddles advice and and its been working a treat. I've had no problems with the 510 pin in my squape but I may have a different version. I got version B from FT I know there was a lot of bad feedback from the version A on FT but that one has now been discontinued.
I really like the simplicity of the Squape I'm just glad I've sorted the flooding issues.

[Dunny]

Apr 7, 2014 21:22:45 GMT spikus said:

Instead of one length of kanthal you use two ... Doubled over ... Hold one end tight then put the other 2 ends in a drill chuck ... Then start the drill and twist the two lengths until it forms a braided length resembling a rope ... Then use that and coil as normal .... It gives the same effect as using dual coils ... I.e halves the resistance ... ... Zoom in on the coil posted and you will see

Ahh.. I get ya. I think I'll have to be giving that a go as well. How many wraps do you use for a 0.9 ohm coil? am I right at 4 looking at the picture?

[spikus]

There's 5 wraps ... Think it was a 2mm drill bit