Origen

[VapingBad]

The Origenny

[yourgurnard]

Re. the O'Genny:- Did n't You Have to Use Oven Cleaner on the 510 Thread to Remove Coating That Was Insulating the Connection? (Shoot Me Down if Me Memory's Wrong!! )

My Ones :-http://www.fasttech.com/products/3028/10008099/1743800 Arrived Today!
Only Just Built One (Been in Pub Most of Day....Worshipping Harry Kane & Then Over-Imbibing!!! ...)
Like it!....Luverly Flavour, Tho' Found it Very Fiddly Wiv Ribbon Wire (Tho' See Above!!!) So Only Single Coil at Present.
Actually, Just as Pleased Wiv the Mini-DID (17mm) Tank That Came Too!...Tho' That'll Get Attacked Wiv Drill Tomorrow as 1x Tiny Little Air Hole Makes it Hard Work!....& Me 2mm S/S Rope Fits Too! (MUST Get Some of the Cutters That VB Posted!!!)

[VapingBad]

Feb 8, 2015 0:10:59 GMT yourgurnard said:

Re. the O'Genny:- Did n't You Have to Use Oven Cleaner on the 510 Thread to Remove Coating That Was Insulating the Connection? (Shoot Me Down if Me Memory's Wrong!! )

The first ones I got yes, but the one I linked too not much came off and it wasn't necessary unless you are running temp limiting nickel coils, but didn't try before and after.  How is the seal between the deck and body - does it leak liquid there?

[yourgurnard]

It Weeps a Bit...........But Only 'cos 1 of the 'O' Rings is Missing!
When I 1st Went to Dis-Assemble it, I Could NOT Pull the Body/AFC Off Of the Base....Did Me Usual:- Put in the Freezer For a While & Then Managed it...........Reason it Was Stuck Was 'cos 'O' Ring Had Been Split & Pushed Down....Jamming it Up!
T'Other One's OK But in Bits in Vodka to Clean B4 Building!

[VapingBad]

Feb 8, 2015 0:33:48 GMT yourgurnard said:

It Weeps a Bit...........But Only 'cos 1 of the 'O' Rings is Missing!
When I 1st Went to Dis-Assemble it, I Could NOT Pull the Body/AFC Off Of the Base....Did Me Usual:- Put in the Freezer For a While & Then Managed it...........Reason it Was Stuck Was 'cos 'O' Ring Had Been Split & Pushed Down....Jamming it Up!
T'Other One's OK But in Bits in Vodka to Clean B4 Building!

Not the top cap but the join between the deck and the aluminium tank body, it was a poor fit on the first ones but good on the second type I got.  The first one liquid comes up around the edge when filling with bottle that seals with the fill hole.

[yourgurnard]

Oh, My Bad!
'Twixt Deck/Bod is Fine...'O' Ring Above AFC Holes Was the One Broken

[geordie_vaper]

gonns try and bag a v3 dripper ment to be released on the 19th if anyone sees any online for sale please let me know

[dagl]

Feb 10, 2015 1:10:19 GMT geordie_vaper said:

gonns try and bag a v3 dripper ment to be released on the 19th if anyone sees any online for sale please let me know

Keep an eye on the classies around the 22nd

[moodyb]

Feb 6, 2015 22:20:02 GMT moodyb said:

Feb 6, 2015 21:39:40 GMT VapingBad said:

Not seen a Wotofo and was unsure about the GearBest one.

Someone over on the ECF Forum bought the GearBest one and didn't have any complaints, so it might be worth the risk.

I ordered one of the GearBest clones over the weekend, so I'll let you know if its any good / has any problems when it arrives.

[moodyb]

GearBest clone arrived today. 18 days with NL Post, which isn't too bad.

If this vapes as well as the dripper I'll be

Not had a chance to coil it yet as it'll need soaked in alcohol overnight to get rid of the machine oil smell.


Sitting beside the Infinite v2 dripper clone. Both sporting a 15mm stumpy drip tip ( from SignatureTips )



The drip tip from a Sat22 clone looks good on it too