for all you squonkers out there, chaalice V3 clones

[sydsut]

Bugger missed this coz I was enjoying a good Squonk.

[Get Off My Cloud]

May 22, 2015 23:16:51 GMT sydsut said:

Bugger missed this coz I was enjoying a good Squonk.

I have a Chalice III clone on the way mate ordered it to try on this OWL squonker jobby to be honest though i'm not particularly sold on this squonking lark, i'll try the Chalice out when it arrives but unless it's something spectacular i think my squonking days are likely over in which case the Chalice is yours for gratis if you want it.

[sydsut]

Very generous of you Get Off My Cloud but I think you'll like it. I'm now waiting on a Zenith 2.5 from FT, order in but not in stock for a few days. After that, who knows. May try to modify a couple of my drippers. Especially the Derringer as cheap as chips but a great vape.

[Get Off My Cloud]

May 23, 2015 0:30:48 GMT sydsut said:

Very generous of you Get Off My Cloud but I think you'll like it. I'm now waiting on a Zenith 2.5 from FT, order in but not in stock for a few days. After that, who knows. May try to modify a couple of my drippers. Especially the Derringer as cheap as chips but a great vape.

I'm sure it'll be decent but it really is going have to be very special or it'll just end up sat in the cupboard unused in favour of regular drippers.
It's been shipped from FT so i should have it next week hopefully.

Speaking of Derringers, i've been chuffing away on mine tonight.

[Deleted]

Received. Lovely

[jeffc]

karlgixer Thank you, it arrived safely, just got to get round to set it up.

Got to watch P.Busardo video on set up. Taking special attention to position of internal cap air hole to the coil position, MUST be inline.




Yes mine was way out with top body unit screwed down. Sanded the top body VERY CAREFULLY using wet / dry paper, now hole lines up with coil. Makes a major improvement to the vapour & flavour.

Good luck to all, ENJOY!!!!

[blakey]

My 2 arrived today, before you build on these check where the airhole is positioned when the top section is screwed on.
Both of mine are off centre and out by a fair bit.fit coils accordingly.
The build quality isn't a patch on the original and the air control provides a tighter draw but works just fine.
They reek of machine oil so make sure you clean them thoroughly.
Don't pack too much cotton in them and make sure that the cotton stays away from the center drain hole else when you release the squonk bottle it'll suck the juice back out of the cotton.
I leave about 3-4mm of cotton either end of the coil and prod it down to the deck.
Won't get a chance to build these clones till tonight but if the coil goes in front of the air hole then they look like they'll perform just nice.

[blakey]

Right, got home from work and hit them both with the emery cloth until the air holes lined up, took 3mins each.
Put both dismantled into a pan of water and boiled the crap out of them for 15mins.
Rinsed and dried
Looking closer at them you can really tell they've used cheap parts and metals but cheap is exactly what they were so no complaints
Coiled and wicked and used on an s-cat and I have to say that they performed admirably, the airflow isn't as open as the genuine but I never open the genuine up all the way so no biggy there and the Vape is very good indeed.
Doubt they'll be of a decent enough quality to run nickel coils but for a cheap as chips kanthal squonking attie I'm finding it hard to rubbish them.

[Deleted]

I've done one of mine thanks to jeffc help. I'll tackle others tomorrow or sometime. Lovely little atties but I still prefer the cyclone