is a sqounker a mech or can you get vv/vw ones ?

[banditruss]

not got one yet ..thinking about it though so wanted to check lie of the land so to speak

[lee]

Well alot depends on the squonker you get etc? Prices range from pretty cheap like the one phatfil linked robby normally has the head's up along with his squonking partner in crime @spikeyfridge or for the ultimate in squonking you could get @windows to make you one??

[phatfil]

for budget clones the zenith V2.5 from fasttech and the chalice3 FT and GB, are 2 Bottom fed attys available there are others but some like the hobo3 dont all arive with the bottom feeding pin fitted or supplied. (zenith v2.5 comes with a spare b/f pin and not with one fitted u change it over..)

[VapingBad]

Unlike the converted drippers the Chalice3 is a proper designed for squonking atty, they have a concave deck and very short wicks so the wick is wetted then the excess liquid is sucked back down the tube. This keeps the liquid in your wick clearer, slightly increases the heat-up time and together with the small chambers these designs allow are the reasons that many believe squonking has better flavour than drippers.

[Deleted]

Jul 14, 2015 13:31:17 GMT lee said:

Well alot depends on the squonker you get etc? Prices range from pretty cheap like the one phatfil linked robby normally has the head's up along with his squonking partner in crime @spikeyfridge or for the ultimate in squonking you could get @windows to make you one??

Oh contraire!!! I've got cheapish geyscano and firebox ones and @windows ones. All are very good but I do prefer the regulated ones for the oomph factor. Waiting on the flask squonker.
Best atty so far is my 14mm cyclone though the zeniths are pretty damn good too!

[banditruss]

well there certainly cheap engough !...but are they good enough rather spend alittle more and give it its best shot ..

[Deleted]

In my opinion, I'd go for a geyscano as a first squonker. Suck it and see. Mine works flawlessly. Only downside is the sharp corners but that's just me. I use mine with a ft zenith 2.5 and have had no issues. Might even get a blue one at some stage if I can find one!

[banditruss]

just looked at the zenith 2.5 on ft and it doesnt look like a bottom feeder ?..then obivois question what differ ence between 2.5 and the v2 ?...i know that the v3 is 28mm....but the other two cant see any difference an niether look like botton feeders....

[Deleted]

Should be a hollow pin which comes out the centre post and screws into the 510 connection. You just swap them over

[phatfil]

Jul 14, 2015 14:00:50 GMT banditruss said:

just looked at the zenith 2.5 on ft and it doesnt look like a bottom feeder ?..then obivois question what differ ence between 2.5 and the v2 ?...i know that the v3 is 28mm....but the other two cant see any difference an niether look like botton feeders....

in the V2.5 the screw used to secure the wire in the central post is hollow and u can just swap that for the screw at the atty bottom in the 510 connector job done  there is also a spare hollow screw in the spares bag too
and due to this its Very popular and can be out of stock/restocking on Ft so order and wait

[banditruss]

ahh right that sounds better didnt look right in pics !...thx

[Deleted]

www.fasttech.com/products/3028/10008591/1901902-zenith-v2-5-styled-rebuildable-dripping-atomizer
If you look at first pic, centre pin is hollow. Take this out, stick it in the other end and bob's a squonker !!!

[banditruss]

lol thx

[VapingBad]

banditruss I have zenith V2.5 from FT only used once I would trade for a Velocity if you are interested.

[banditruss]

sry mate not sorted yet just prilimary questions should i go that route ...not made my mind up yet ..it if the telsa 160w doesnt sell i might swap for sqounker just to try..