Recommendations for a MTL RTA please..

[firewall]

Erlkönigin was great for mtl but like decoy says clone are very hit and miss. Does take effort to get the haircut right but then it's a great vape.

[maxlawbr]

Jul 3, 2016 17:54:05 GMT decoy said:

have the kayfun v3 mini clone and its a belter but an odd size, the v5 is 22mm and more or less identical but bigger so should be easier to work on
erokin have some very good tanks that are top fill and have a very easy build deck, the clones are hit and miss but a genuine can be got for under £30
the ks tank clone is very easy to build has huge capacity and is short but it only suits box mods
mini goblin can be set up to do mtl single coil and is rather good at it but its a pig to lean how to build this sucker so it don't leak but well worth it as it can also do duel coil lung hits

for smaller tanks (17 m gizmo) miniatty clone and mini fogger are both good but again tricky as build decks are tiny

I tend to vape around 1 ohm mtl on a mech


Hi Decoy,


I Have miniatty but it is too tricky, I can't build it properly without dryhits. would you mind to tell me how you wick it?


Thanks

[decoy]

Aug 5, 2016 0:10:51 GMT maxlawbr said:

Jul 3, 2016 17:54:05 GMT decoy said:

have the kayfun v3 mini clone and its a belter but an odd size, the v5 is 22mm and more or less identical but bigger so should be easier to work on
erokin have some very good tanks that are top fill and have a very easy build deck, the clones are hit and miss but a genuine can be got for under £30
the ks tank clone is very easy to build has huge capacity and is short but it only suits box mods
mini goblin can be set up to do mtl single coil and is rather good at it but its a pig to lean how to build this sucker so it don't leak but well worth it as it can also do duel coil lung hits

for smaller tanks (17 m gizmo) miniatty clone and mini fogger are both good but again tricky as build decks are tiny

I tend to vape around 1 ohm mtl on a mech


Hi Decoy,


I Have miniatty but it is too tricky, I can't build it properly without dryhits. would you mind to tell me how you wick it?


Thanks

you have to use a lot less cotton than you think
I use a long thin strip
feed it throw the coil
poke both ends in to the holes with a small screwdriver
pull it out the bottom of the juice holes and leave it with no tension throw the holes and coil
trim as short as you can and spread the ends
I had same prob as you but just keep using less and less cotton and poss a higher ohm coil and youll find its sweet spot

[maxlawbr]

Thanks a lot Decoy.

I'll try it, with much less cotton. Let's see, I'll keep in touch and give you the proper follow up.

Thanks a lot.

[decoy]

Aug 11, 2016 1:42:44 GMT maxlawbr said:

Thanks a lot Decoy.

I'll try it, with much less cotton. Let's see, I'll keep in touch and give you the proper follow up.

Thanks a lot.

I can put up pics next time I redo it but tbh its just a case of using less and less cotton
if its not leaking chances are to much cotton lol

[Lee]

The Protank 4 has a decent review by PBusardo for MTL



Plus they take the single coil RBA from the subtanks

I don't own one myself

[Pepperty]

I happily MTL on subtanks (and nano and v2 and mini's - they all use the same rebuildable deck)

Most of mine have one air slot and option to set to small hole/large hole/2 holes/ or slot so I just build above 0.5 and mouth-to-lung on small hole. The advantage of them is the rebuildable and replaceable rba coil, its also their disadvantage as a few of mine now have connection issues but they have had a years hammering so I can just nip onto Fasttech and order some replacements...

[maxlawbr]

Decoy,

I build my miniatty today acording your instructions, it is performing very well. 1.2 ohms, less cotton, put down on holes and pull out the wick outside the chanel.

I took some pics of the cotton and the wick outside the chanel, I'll post here soon.

Thanks again Decoy.