neofolis
New Member
Joined:January 2013
Posts: 6
Location:
Recent Posts
Last Online Feb 22, 2013 22:55:36 GMT
|
Post by neofolis on Feb 7, 2013 21:30:09 GMT
Thanks for your efforts everyone, I'll try to get some pics sorted, probably not until tomorrow though.
|
|
neofolis
New Member
Joined:January 2013
Posts: 6
Location:
Recent Posts
Last Online Feb 22, 2013 22:55:36 GMT
|
Post by neofolis on Feb 7, 2013 17:00:35 GMT
Sorry, I'm still having an issue with this. Basically when I screw the ceramic holder into the base I should have the positive pin protruding from the 510 connection very slightly, but if I do that there is no air flow. I have to back it off a full turn before I get air flow, at which it is a totally open draw and the positive pin is no longer protruding from the base. Any ideas what I'm doing wrong, I assume it can't be a manufacturing fault, otherwise they'd all be like it. have you got the o-ring tight up against the knurled locking ring on the ceramic housing unit cos if you have it sat in the groove at the bottom of the unit it will cause an air tight seal? Yes, it's tight against the locking nut, but it's like the positive pin is not long enough, because, by the time it's screwed in far enough to make contact with the positive part of the 510 I'm screwing it into, that O ring is totally blocking any air flow and is being squeezed between the knurled locking nut and the groove at the bottom. |
|
neofolis
New Member
Joined:January 2013
Posts: 6
Location:
Recent Posts
Last Online Feb 22, 2013 22:55:36 GMT
|
Post by neofolis on Feb 7, 2013 16:56:42 GMT
I don't really know the answer to your problem Neo, is this the Choddy, not the Nautilis or Terminator? But a couple of questions, what are you screwing it into and have you tried it with an adapter? It's the Chinese version, there is no air flow even when it's not screwed into anything. |
|
neofolis
New Member
Joined:January 2013
Posts: 6
Location:
Recent Posts
Last Online Feb 22, 2013 22:55:36 GMT
|
Post by neofolis on Feb 7, 2013 6:00:00 GMT
Sorry, I'm still having an issue with this. Basically when I screw the ceramic holder into the base I should have the positive pin protruding from the 510 connection very slightly, but if I do that there is no air flow. I have to back it off a full turn before I get air flow, at which it is a totally open draw and the positive pin is no longer protruding from the base. Any ideas what I'm doing wrong, I assume it can't be a manufacturing fault, otherwise they'd all be like it.
|
|
neofolis
New Member
Joined:January 2013
Posts: 6
Location:
Recent Posts
Last Online Feb 22, 2013 22:55:36 GMT
|
Post by neofolis on Feb 6, 2013 16:20:01 GMT
Yes, I am aware of this, what I am saying is that when the mouth piece is closed, there is no air flow, so if I open it, it would try to suck air through the juice and suck loads of juice onto the coil, flooding it. I think I have worked it out anyway. I think I had the ceramic holder screwed too far into the base and it was shutting off the air flow, I assume, because the O ring on the positive terminal was blocking it.
|
|
neofolis
New Member
Joined:January 2013
Posts: 6
Location:
Recent Posts
Last Online Feb 22, 2013 22:55:36 GMT
|
Post by neofolis on Feb 6, 2013 14:14:10 GMT
Can someone explain to me the air path, because I have the Chinese version and having read that the air flow is controlled by the height of the positive pin, I moved that down as far as it would go to give an airy draw, but the furthest it will go down is with only a very slight part protruding and when I close the mouth piece I get no air flow at all. I don't actually want a particularly airy draw, but I was trying to wind the positive post down more to get some air flow and it's just not happening. I see there is a small hole in the centre of the positive post but surely the air doesn't go in through that and obviously it doesn't go between the positive post and the negative, because there is an O ring sealing in between, so I'm a little confused. Sorry if the answer is in the thread somewhere, I have read most pages a couple of times and not found anything.
|
|
