dannyw14
Senior Member
Joined:April 2013
Posts: 485 
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 22:57:12 GMT
Not got any wd40 but i'm guessing that'd probably cost the same asd a pare of plier Hi Danny. If you don`t have any pliers, try the following. Get gas lighter, heat up slowly the `nut`, then wearing a glove for protection against the heat, unscrew the `nut`. (take care it will be hot). It`s an old `dodge` engineers have been doing for years, and it worked every time for me on sticking/locked `nuts`. Good luck. jeffc Would that not affect the integrity of the thread? |
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 22:51:17 GMT
Jurojin are really good, kind of a cross between System of a down and Tool.
A band that i didn't really like to start with but they've grown on me recently, plus I'm seeing them at download next week:
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 12:44:54 GMT
Ah I'll have to try that then. Although I am very pleased with how the Protank is performing right now, probably the best since i got it.
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 12:30:09 GMT
I made sure the wick was short enough to fit in the well that the head sits into as well. I'm not getting on with ekowool too well as no matter how much i flame it, i can't seem to get it to roll into a tube shape, and it doesn't seem to coil very well flat
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 12:28:36 GMT
I tried using ekowool and it just wouldn't wick at all, but put the head into an evod and it worked fine
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 12:26:37 GMT
I've got a spare but need to get this one off first. I'll try washing up liquid now....
Nope, didn't work, pliers it is
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 11:44:38 GMT
Put some dishwashing gloves on and try instead of pliers.. Haha I've tried that, it still wouldn't budge |
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 11:43:01 GMT
Just thought i'd post this as I've discovered something today.
I usually use 3mm silica with a few strands on top to recoil my Protanks heads. I did some shopping yesterday and today I've tried recoiling using 2mm silica with a 2mm piece on top and it seems to work alot better straight away. I'm vaping Fluffy Nuts from ChefsVapour at 8 watts and it's tasting really good.
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 11:18:33 GMT
I've not got any pliers but I'll try and get some and have a go with them
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 11:16:32 GMT
yeah the knurled nuts, the post is not inside the device it's seperate, i screwed the nuts back on just to keep them safe, the first two were fine but the third one is stuck
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 8, 2013 11:02:02 GMT
Does anyone know anywhere i can get a replacement centre post for an Aga-T2? As i've just tried to put mine back together after cleaning it and i just cannot get the last screw of the centre post off, so I'm assuming the thread is broken
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 7, 2013 9:53:06 GMT
I'm buying some 400 mesh for the Aga and RSST, from the vape mesh company. Do i need 25 or 30 micron?
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 6, 2013 19:31:47 GMT
What i'm going to do is a keep it as it is for a bit longer and see how it goes, if i still don't like it on monday i'll drill it out.
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 6, 2013 15:20:15 GMT
Guess i'll go and source a drill bit then. should i be going for 1.2mm?
|
|
dannyw14
Senior Member
Joined:April 2013
Posts: 485
Location:
Likes: 85
Recent Posts
Last Online Jun 19, 2017 18:28:00 GMT
|
Post by dannyw14 on Jun 6, 2013 15:10:57 GMT
Thank you very much, It will be a massive help.
|
|
