peter12
Super Member
Joined:August 2015
Posts: 500
Location:
Likes: 176
Recent Posts
Last Online Jul 21, 2017 2:22:49 GMT
|
Post by peter12 on Sept 13, 2015 17:11:02 GMT
Seems the lemo 2 and billow my misses is using keep leaking on her. Nothing of biblical proportions but always from the base area. I stripped them down completely checked o rings. Cleaned them. Did this 2 or 3 times and nothing worked.
Turns out when they make the sizzling noise she has been holding the power button and blowing into the drip tip to stop it "hissing" at her. I guess once or twice she must have got hot juice spit in her mouth.
Anyways I'm hopeful that this is the route cause of the issue. Fingers crossed no more leaks ;p
They did have occasional leaks when I used them, but I solved rhat before passing them to her. Think that was a wicking issue.
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Jun 1, 2024 20:23:54 GMT
|
Post by Deleted on Sept 13, 2015 17:29:38 GMT
I find with the lemo 2 you have to be careful when refilling to avoid subsequent leaking .. Ensure the AFC is closed, fill slowly at an angle and leave an air bubble just as you would when filling a kayfun.
|
|
peter12
Super Member
Joined:August 2015
Posts: 500
Location:
Likes: 176
Recent Posts
Last Online Jul 21, 2017 2:22:49 GMT
|
Post by peter12 on Sept 13, 2015 17:34:51 GMT
I find with the lemo 2 you have to be careful when refilling to avoid subsequent leaking .. Ensure the AFC is closed, fill slowly at an angle and leave an air bubble just as you would when filling a kayfun. You don't find it best to fill whilst on its side ? Will try on a 45 degree angle next time then
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Jun 1, 2024 20:23:54 GMT
|
Post by Deleted on Sept 13, 2015 17:39:35 GMT
I find with the lemo 2 you have to be careful when refilling to avoid subsequent leaking .. Ensure the AFC is closed, fill slowly at an angle and leave an air bubble just as you would when filling a kayfun. You don't find it best to fill whilst on its side ? Will try on a 45 degree angle next time then I know that is what Eleaf suggest as a way of getting maximum juice into it but I tried it that way a couple of times and each time it didn't exactly leak but wept juice from the AFC slot so I went back to the tried and tested kayfun method and it has been fine every time since.
|
|
peter12
Super Member
Joined:August 2015
Posts: 500
Location:
Likes: 176
Recent Posts
Last Online Jul 21, 2017 2:22:49 GMT
|
Post by peter12 on Sept 13, 2015 17:45:02 GMT
@yinyang yes that exactly what happens with mine. Juice seeps through the AFC ring and then ends up between base and mod. Not loads but enough to be an issue
Will try filling on an angle from now on
Never seen the kayfun3thod so not sure on that.sorry
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Jun 1, 2024 20:23:54 GMT
|
Post by Deleted on Sept 13, 2015 17:53:25 GMT
Just hold the lemo at an angle Peter and fill slowly allowing the air to be expelled by the incoming juice. Watch the air bubble inside the tank slowly rise as you fill and stop filling just before the bubble would disappear. Straighten up the tank, close the filler and open the AFC. .. Job done.
|
|
tim
Super Member
Joined:February 2015
Posts: 2,137
Location:
Likes: 1,516
Recent Posts
Last Online May 25, 2022 22:18:37 GMT
|
Post by tim on Sept 13, 2015 20:30:51 GMT
Just hold the lemo at an angle Peter and fill slowly allowing the air to be expelled by the incoming juice. Watch the air bubble inside the tank slowly rise as you fill and stop filling just before the bubble would disappear. Straighten up the tank, close the filler and open the AFC. .. Job done. I fill my Lemo 2's until juice appears at the fill slot, then let some juice get sucked back into the bottle, just enough to allow me to close it without it dripping down the side of the tank. Not had many leaks with them, only when I first filled them, which was a wicking issue (not enough to stop flooding). I do close the AFC first, and vape on it for 3 or 4 draws afterwards to get the vacuum back. HTH
|
|
phatfil
Super Member
Joined:April 2015
Posts: 2,874
Location:
Likes: 1,941
Recent Posts
Last Online May 29, 2024 18:48:15 GMT
|
Post by phatfil on Sept 13, 2015 21:47:23 GMT
+1 close the air in ring before opening the top.....
|
|