buckowski
Super Member
Joined:February 2010
Posts: 657
Location:
Likes: 56
Recent Posts
Last Online Aug 6, 2019 18:16:55 GMT
|
Post by buckowski on Jun 9, 2013 18:23:57 GMT
Has anyone come across this before?... My zmax just stopped working. It's reading ohms at 9.9 with and without atomiser attached. No load I'm guessing. Is this a well known type of fault and is there a fix? Gutted, was working great as well  |
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 22, 2024 23:11:17 GMT
|
Post by Deleted on Jun 9, 2013 18:28:04 GMT
Haven't got a Zmax but have you tried anything else on it. The coil might have popped and will need recoiling or the center pin might need lifting up a bit to read any ohm's. They be others along with knowledge of a zmax.
Good luck
|
|
fizzygirl
Junior Member
Joined:May 2013
Posts: 95 
Location:
Likes: 32
Recent Posts
Last Online Jul 19, 2014 21:02:06 GMT
|
Zmax help
Jun 9, 2013 18:38:02 GMT
via mobile
Post by fizzygirl on Jun 9, 2013 18:38:02 GMT
Have you tried a different atomiser cos without out one it will read 9.9 if.the centre pin int touching it will read 9.9
|
|
buckowski
Super Member
Joined:February 2010
Posts: 657
Location:
Likes: 56
Recent Posts
Last Online Aug 6, 2019 18:16:55 GMT
|
Post by buckowski on Jun 9, 2013 19:00:02 GMT
I just tried every atomiser I own, managed to get the igo-l working, but the other 5 are not being recognised. So I guess the centre pin has been pushed down too far somehow, tried to lift it but can't figure out how to, awkward inside there  . Ahh bugga. |
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 22, 2024 23:11:17 GMT
|
Post by Deleted on Jun 9, 2013 19:04:12 GMT
I just tried every atomiser I own, managed to get the igo-l working, but the other 5 are not being recognised. So I guess the centre pin has been pushed down too far somehow, tried to lift it but can't figure out how to, awkward inside there . Ahh bugga. hope this helps |
|
buckowski
Super Member
Joined:February 2010
Posts: 657
Location:
Likes: 56
Recent Posts
Last Online Aug 6, 2019 18:16:55 GMT
|
Post by buckowski on Jun 9, 2013 19:30:09 GMT
Blimey, i tried that Taz, but I succeeded in making the pin go further down, now nothing works haha. What a day, think i'll have an early night before I break more stuff  |
|
maccafan
Super Member
Joined:May 2012
Posts: 6,278
Location:
Likes: 469
Recent Posts
Last Online Nov 3, 2022 10:25:09 GMT
|
Post by maccafan on Jun 9, 2013 19:44:09 GMT
The hard nylon top hat washer is probably broken. If you are having no luck whatsoever, you can send it to me and I can fix it for you for the cost of postage both ways.
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 22, 2024 23:11:17 GMT
|
Post by Deleted on Jun 9, 2013 19:47:39 GMT
The hard nylon top hat washer is probably broken. If you are having no luck whatsoever, you can send it to me and I can fix it for you for the cost of postage both ways. That is a superb gesture maccafan.  |
|
buckowski
Super Member
Joined:February 2010
Posts: 657
Location:
Likes: 56
Recent Posts
Last Online Aug 6, 2019 18:16:55 GMT
|
Post by buckowski on Jun 9, 2013 19:53:16 GMT
The hard nylon top hat washer is probably broken. If you are having no luck whatsoever, you can send it to me and I can fix it for you for the cost of postage both ways. Ah man that would be amazin Macca, I was resigned to chuckin it, I'll give you a pm, thanks mate  |
|
. Ahh bugga.
