Protank not working on SVD.

[zeldamum]

Has anyone experienced their Protank not working on an SVD.

It works on Ego batteries so I know its not the Protank and other clearos work on the SVD.

[Bluefish]

Take a look at the center pin is it sticking out far enough? If not refit the atty coil and screw it in a bit further.

[Super-Shiny]

If you have a spare genuine evod head remove the part in the picture below and put it into the protank one, they seem to be a different design, worked for me.



Piccy of protank bottom part, as you can see it is slightly chanfered around the edges:

[zeldamum]

Raised the centre pin and still nothing.

I will try your suggestion Romelee.

[zeldamum]

Aug 22, 2013 8:34:40 GMT Super-Shiny said:

If you have a spare genuine evod head remove the part in the picture below and put it into the protank one, they seem to be a different design, worked for me.



Piccy of protank bottom part, as you can see it is slightly chanfered around the edges:

Its working now, undid it to do as you suggested Romelee and no little extra bit so put it back in and now its working So i guess I didn't screw it in tight enough in the first place.

Thank you.

[Super-Shiny]

Worst scenario zeldamum if it is the Mini Protank you can use fine sandpaper and sand the bottom of the base a fraction until it works.

[Super-Shiny]

[zeldamum]

It really looks good on the SVD and vapes well.

ETA: One thing I like about it is you can change the head without getting juice over everything

[chykensa]

Abso-bloomin-lutely zeldamum - just got to figure out what to do with the tank bit while my hands are full - any suggestions, peeps?

[Super-Shiny]

Aug 22, 2013 10:42:48 GMT chykensa said:

Abso-bloomin-lutely zeldamum - just got to figure out what to do with the tank bit while my hands are full - any suggestions, peeps?

Do you mean filling it?

[zeldamum]

Oh dear good job fiddles isn't around

Put the head on a tissue whilst filling the tank.

[andym]

Mine arrived today,well impressed despite it being a bit of an airey draw,plenty of Vapour and the taste is improving by the minute.Vaping at a very lowly 3.6 volts on my SVD,and it looks real nice on it as well,i may have to invest in another.A minor gripe was i ordered the V2 version but got the V1 version.TBH im not all that bothered,otherwise excellent service from Mypack!

[andym]

DOH!Just checked and i DIDNT order the V2 LOL ,so thats a job for tomorrow cos its payday!

[chykensa]

No, I mean if it's got some juice in it already - can't just lay it down, it will dribble everywhere
I've tried to find a bottle which I can cut down, but the necks are all too wide . . . I'll keep working on it!

[Super-Shiny]

Aug 22, 2013 17:50:47 GMT chykensa said:

No, I mean if it's got some juice in it already - can't just lay it down, it will dribble everywhere
I've tried to find a bottle which I can cut down, but the necks are all too wide . . . I'll keep working on it!

With all Evods and Protanks i do the following when re-filling:

1: Drip tip facing downwards and take base off
2: Put the Evod/Protank on a flat surface drip tip downwards
3: (Don't need to do this if it is the first fill and is condensation free) Get tissue and roll up into a spear and then get the Evod/Protank and push the spear of tissue right down the middle tube and give the tissue a twist to gather up all condensation
4: Repeat 2
5: Get the juice and syringe out the amount i need
6: Fill up the Evod/Protank and put base back on and screw up tightly
7: Leave for a couple of minutes for the juice to set in again
8: Vape away