Protank not working on SVD.

[richieh]

To solve the airey draw put a tiny piece of Sellotape over the holes in the dark chrome on the mini protank ( there are 3 of them so one hole at a time is best till you get it just so)
Also a little PTFE tape on the battery threads works really well- this also applies to the full sized protank.
I have both the mini and full size and it has tightened up the draw beautifully for me.
Cheers Richie

[Super-Shiny]

Aug 22, 2013 18:09:40 GMT richieh said:

To solve the airey draw put a tiny piece of Sellotape over the holes in the dark chrome on the mini protank ( there are 3 of them so one hole at a time is best till you get it just so)
Also a little PTFE tape on the battery threads works really well- this also applies to the full sized protank.
I have both the mini and full size and it has tightened up the draw beautifully for me.
Cheers Richie

Can just put candle wax in one or two of the holes, nice and tidy that way

[richieh]

Aug 22, 2013 10:42:48 GMT chykensa said:

Abso-bloomin-lutely zeldamum - just got to figure out what to do with the tank bit while my hands are full - any suggestions, peeps?

Smallish piece of polystyrene(or other packing material) with a hole punched in using copper pipe ,insert protank in upside down and Roberts your mothers bother as they say  
Cheers Richie 

[richieh]

Aug 22, 2013 18:12:31 GMT Super-Shiny said:

Aug 22, 2013 18:09:40 GMT richieh said:

To solve the airey draw put a tiny piece of Sellotape over the holes in the dark chrome on the mini protank ( there are 3 of them so one hole at a time is best till you get it just so)
Also a little PTFE tape on the battery threads works really well- this also applies to the full sized protank.
I have both the mini and full size and it has tightened up the draw beautifully for me.
Cheers Richie

Can just put candle wax in one or two of the holes, nice and tidy that way

Wasn't sure if the wax might melt on an extended vape session so didn't fancy that route but if it works then alls good.
 Just didnt like the idea of  unnecessary vaping of petrochemicals .
 Cheers Richie 

[Super-Shiny]

Tried and tested richieh works fine and does not melt

[richieh]

Aug 22, 2013 18:20:26 GMT Super-Shiny said:

Tried and tested richieh works fine and does not melt

Does it fractionally distillate at lower(vaping )temps tho evolving noxious chemicals  lol
 cheers Richie 

[chykensa]

Aug 22, 2013 18:15:34 GMT richieh said:

Aug 22, 2013 10:42:48 GMT chykensa said:

Abso-bloomin-lutely zeldamum - just got to figure out what to do with the tank bit while my hands are full - any suggestions, peeps?

Smallish piece of polystyrene(or other packing material) with a hole punched in using copper pipe ,insert protank in upside down and Roberts your mothers bother as they say  
Cheers Richie 

That's the baby richieh - will give that a go *disappears to garage with determined look on face!*

[Super-Shiny]

Aug 22, 2013 18:25:05 GMT richieh said:

Aug 22, 2013 18:20:26 GMT Super-Shiny said:

Tried and tested richieh works fine and does not melt

Does it fractionally distillate at lower(vaping )temps tho evolving noxious chemicals  lol
 cheers Richie 

I am still alive if that helps

[andym]

Swapped the SVD collar for the Plinth that came with the tank,works fine.

[zeldamum]

Aug 22, 2013 19:44:10 GMT andym said:

Swapped the SVD collar for the Plinth that came with the tank,works fine.

I did that but it still didn't work, it was purely me not tightening the head enough.

[andym]

I am slowly getting used to it being a far cooler vape after using Vivi Novas exclusively.I really do like this tank.