Mechanical mod for Christmas

[Dan]

Hey guys,

I need some help please!

Looking for some recommendations for a new mechanical mod.. kids have asked me what I want for Christmas! 

Requirements are as follows..

23mm diameter
Airflow control
Adjustable centre pin
Side firing button (located at top and must be lockable!)
Ability to take 18350 & 18500 batteries with a kick
minimal voltage drop
Brushed finish 

Budget is going to be around £150 including kick and batteries

Any ideas?

[Deleted]

That's a very specific list, i can't think of one off the top of my head with a top button.

The Roller is the only one i can think of, but it doesn't come with airflow control as far as i know and it's 22.7mm

[ChillerVapes]

The bolt on fasttech has a top button but it's only £9ish
That means £141 left for a nice top notch tank lol

[blakey]

Atmomixani 69 mod fits them requirements

[Fallen Angel]

Might be a bit over your budget but there is the "my point" touch mod complete with the design of your choice on the body details about it are on the UKV forum here

[Griff]

Some nice Sigelei MOD`s at Health Cabin for £15.08 each.....you could have them all

Health Cabin also do the Smoktech Kick Clone for £10.49.
Griff

[Dan]

digiw0rx I'm very picky! I only want the airflow for the terminators as they are my all day vapes..

Saying that, I suppose I could ask for a hercules to top it off

ChillerVapes Griff I'm looking for something that I wouldn't normally consider buying because of the price.. already have two evics and one svd so looking for something a bit more special.. I am looking at a cheaper option for out and about though so suggestions are very gratefully received!

blakey very nice!!! Definite contender! (Will the terminator-c sit flush or will I still have a gap?)

Fallen Angel that's 20mm so not wide enough... lovely design though!!

[Super-Shiny]

Oct 4, 2013 16:33:10 GMT Dan said:

blakey very nice!!! Definite contender! (Will the terminator-c sit flush or will I still have a gap?)

Don't think you will get rid of that gap as the terminator as that little ridge at the bottom, think the only way would be a mod that has a well around the 510 connection so that the 510 can be sanded down a bit, i only achieved this with the Magneto as the 510 connector air holes was very deep with the upgraded head which enabled me to sand it down a bit without blocking the air holes.

[dave]

The Atmizoo Roller (or perhaps the Dingo?) and the Atmomixani 69 are the only ones I can think of too. There are some very nice bottom button mods about though

[Dan]

Oct 4, 2013 16:41:40 GMT Super-Shiny said:

Oct 4, 2013 16:33:10 GMT Dan said:

blakey very nice!!! Definite contender! (Will the terminator-c sit flush or will I still have a gap?)

Don't think you will get rid of that gap as the terminator as that little ridge at the bottom, think the only way would be a mod that has a well around the 510 connection so that the 510 can be sanded down a bit, i only achieved this with the Magneto as the 510 connector air holes was very deep with the upgraded head which enabled me to sand it down a bit without blocking the air holes.

This is what worried me..

I can get mk2 bases from America (when they come into stock) but it would cost £70 + shipping for 5 of them..

Would be cheaper to buy an ithaka clone!

[Dan]

Oct 4, 2013 17:05:05 GMT dave said:

The Atmizoo Roller (or perhaps the Dingo?) and the Atmomixani 69 are the only ones I can think of too. There are some very nice bottom button mods about though

Do you know the diameter of the roller/dingo per chance? Can't find an answer on atimizoo's site..

I had a drawtube with bottom button and couldn't get on with it.. prefer top buttons..

[Super-Shiny]

Think the Dingo is 23mm Dan

[Super-Shiny]

Dan

Dingo: Dimensions: D: 22.7mm L: 64mm. Weight: 73g.
Roller: Dimensions: D: 22.7mm L: 69mm (18350), 77mm (18500), 93mm (18650). Weight: 74g.

[odj]

I second the 69 I have one and its a cracking mod!