Kayfun mini AAAGGHH!

[OneDay]

Jun 28, 2014 16:51:09 GMT csmith10 said:

Less wick, still burnt... Huff

Are you getting the new wick nice and wet with juice before you put the chimney and tank on?

[csmith10]

Jun 28, 2014 17:16:32 GMT OneDay said:

Jun 28, 2014 16:51:09 GMT csmith10 said:

Less wick, still burnt... Huff

Are you getting the new wick nice and wet with juice before you put the chimney and tank on?

Yep, saturating it, I think this is what's giving the first few good vapes, after that its all down hill

[Di]

csmith10 

Have you seen the post richo71 has done about the Kayfun mini clone?

allaboute-cigarettes.proboards.com/thread/41260/kayfun-clone-ivogo-youtube-review?page=1&scrollTo=716525

[csmith10]

Jun 28, 2014 19:26:21 GMT Di said:

csmith10 

Have you seen the post richo71 has done about the Kayfun mini clone?

allaboute-cigarettes.proboards.com/thread/41260/kayfun-clone-ivogo-youtube-review?page=1&scrollTo=716525

Right I give up, I think I've got a duff tank! I just followed that video too a tee but when filling it with the clear tank I can't get the air bubble to rise when I turn it upside down! I also have a small air bubble where the pastic and metal sections connect. It's almost if the chimney is to wide or the plastic tank is to narrow, I'm also getting air bubbles coming out of the chimney where the juice is drawn in! Is that normal?

[csmith10]

This is with the top section full of juice

[OneDay]

csmith10

[chrisjw]

Ditch all that micro-coiling malarky & go back to good old silica with a navy nest..............I only use Kayfun's, be they lites, 3.1's, mini's etc & I've always used that method...........never had a dry hit, a bad vape or any problems whatsoever......My personal opinion is that cotton & micro-coils are overrated & too much hassle..........but that's my opinion only............I prefer a hassle free life.



"Life...........is just a bowl of tricks!!!!!!"

[richo71]

Jun 28, 2014 20:42:38 GMT csmith10 said:

Jun 28, 2014 19:26:21 GMT Di said:

csmith10 

Have you seen the post richo71 has done about the Kayfun mini clone?

allaboute-cigarettes.proboards.com/thread/41260/kayfun-clone-ivogo-youtube-review?page=1&scrollTo=716525

Right I give up, I think I've got a duff tank! I just followed that video too a tee but when filling it with the clear tank I can't get the air bubble to rise when I turn it upside down! I also have a small air bubble where the pastic and metal sections connect. It's almost if the chimney is to wide or the plastic tank is to narrow, I'm also getting air bubbles coming out of the chimney where the juice is drawn in! Is that normal?

Sorry i cant help you out any further than what i showed in my video, out of interest what ratio pg/vg is your juice? what ohms is your micro coil? when you push the tails of the cotton back in just push them in lightly.  There is slightly more room around the bottom of the tank using the ss tank sections. sorry i cant help you further but when you get it going it is a cracking vape, i would aim for a 1.2-1.4 ohm micro coil in there

[csmith10]

My current coil is 1.2ohm and I followed your video too a tee, my wick looked exactly like yours did! I think there's something not right with this mini clone!

[csmith10]

Jun 28, 2014 21:07:41 GMT OneDay said:

csmith10

Yeah the bubbles form then disappear back in the chimney

[hijack]

Jun 28, 2014 20:52:09 GMT csmith10 said:

This is with the top section full of juice

Surley if there is juice in the top section then there shouldn't be an air gap separating the juice in the top from the juice in the bottom. I cant even figure how that can happen. ??? Is it just me? cant anyone else see that?

Is that the FT mini? and is it the $14 one or the $24 one?

[csmith10]

Its the IVOGO clone

[hijack]

csmith10 and that is a big air gap im seeing separating the juice in the top from the bottom?

[geordie_vaper]

try undoing the chimney a turn or two

[richo71]

Jun 28, 2014 21:36:55 GMT hijack said:

csmith10 and that is a big air gap im seeing separating the juice in the top from the bottom?

Yeah, there should not be an air bubble mid section. i would syringe the juice out and start again, just to make sure and for peace of mind