From Gearbest ref Kayfun 4 :(

[jbryenton]

Thanks, I'll strip it down a give it a few cycles in the ultrasonic cleaner then. ?

[Roscopecotrain]

Just coiling mine up from gearbest as we speak.

[jeffc]

jbryenton Good video on the Kayfun V4, will help you strip down and set up.

www.toddsreviews.com/2014/11/the-kayfun-v4.html


Enjoy.

[jbryenton]

Thanks, looks straight forward enough, just about mastered my hcigar kayfun lite plus v2 (can an atty name get any longer!) So should be good.

[Tom]

Mine came today.

Absolutely remarkable copy of the clone. Great threading, looks brilliant. The juice shut off twist seems a little stiff but will probably loosen with use.

Not sure whether to coil it and keep as a mouth to lung atty or just keep boxed unused and pass it on.

How are yours performing chaps?

[Roscopecotrain]

Jan 17, 2015 19:32:18 GMT Tom said:

Mine came today.

Absolutely remarkable copy of the clone. Great threading, looks brilliant. The juice shut off twist seems a little stiff but will probably loosen with use.

Not sure whether to coil it and keep as a mouth to lung atty or just keep boxed unused and pass it on.

How are yours performing chaps?

Mine was stuck solid. Had to dismantle the whole bottom section and now not sure i have it back right as it does not spin much on the juice control section.

Been told i have to leave it for today lol.

[Tom]

Jan 17, 2015 19:40:13 GMT Roscopecotrain said:

Jan 17, 2015 19:32:18 GMT Tom said:

Mine came today.

Absolutely remarkable copy of the clone. Great threading, looks brilliant. The juice shut off twist seems a little stiff but will probably loosen with use.

Not sure whether to coil it and keep as a mouth to lung atty or just keep boxed unused and pass it on.

How are yours performing chaps?

Mine was stuck solid. Had to dismantle the whole bottom section and now not sure i have it back right as it does not spin much on the juice control section.

Been told i have to leave it for today lol.

Lol.

I took mine to bits when it arrived... as one does xD

Make sure you use the screwdriver in the air hole section the first time you take the deck out. For the first couple of turns its basically impossible to do without.

That was similar on the original, maybe slightly easier.

A little juice on the o ring underneath helps it out a lot.

Good luck bud.

[wight]

Jan 17, 2015 19:40:13 GMT Roscopecotrain said:

Jan 17, 2015 19:32:18 GMT Tom said:

Mine came today.

Absolutely remarkable copy of the clone. Great threading, looks brilliant. The juice shut off twist seems a little stiff but will probably loosen with use.

Not sure whether to coil it and keep as a mouth to lung atty or just keep boxed unused and pass it on.

How are yours performing chaps?

Mine was stuck solid. Had to dismantle the whole bottom section and now not sure i have it back right as it does not spin much on the juice control section.

Been told i have to leave it for today lol.

Mine was really stiff as well. I undone the 510 by maybe 1/2 to 1 whole turn just to open and close the juice flow bit of a pita to undo the screw a little bit every time you want to fill but hopefully it will turn naturally after a while
Also I took the air flow screw out compleaty.
Really nice attie very pleased so far

[Roscopecotrain]

Jan 18, 2015 10:22:21 GMT wight said:

Jan 17, 2015 19:40:13 GMT Roscopecotrain said:

Mine was stuck solid. Had to dismantle the whole bottom section and now not sure i have it back right as it does not spin much on the juice control section.

Been told i have to leave it for today lol.

Mine was really stiff as well. I undone the 510 by maybe 1/2 to 1 whole turn just to open and close the juice flow bit of a pita to undo the screw a little bit every time you want to fill but hopefully it will turn naturally after a while
Also I took the air flow screw out compleaty.
Really nice attie very pleased so far

It is quite a tight draw with it all the way open i must admit. Good job i like a tighter draw. Seemed to have sorted bow and all back as it should be with a smooth juice flow control.

[lisburnvapes]

My gear best kayfun4 arrived yesterday , ordered in mid December , dispatched 7th January, so all in all about a months wait in total.
First impressions are very good, it looks and feels excellent quality , well boxed and comes with spares and instruction booklet.
Have yet to set it up but for just over £11 delivered it seems brilliant value, big thanks to robby for the heads up !

[jeffc]

Hi Peeps. I`ve just removed the 510 pin to allow adjustment of the AFC slot head screw,beneath it.

Unscrewed it by 2 turns, then re-installed the 510 pin.

Completely transforms the vape,masses of flavour along with vapour.

Takes only seconds but really well worth it.

Enjoy your V4 peeps.

[jbryenton]

Just got home from work and there was a package waiting for me. The Kayfun V4 is currently in pieces bathing in the ultrasonic with a good dose of Fairy Platinum. Juice control was locked solid when I first took it out of the box but that can be addressed when I rebuild it shortly.?

[iLardyboy]

Mine came on Saturday and I'm really impressed with the quality of this clone. I did have the original for a while and this is an exact copy of it. The threads are excellent and everything works as it should. It was really badly covered with machine oil, but a good clean sorts it out. I've been using it quite a bit since Saturday and I've had absolutely no issues. The build I'm using is a 5/4 standard wrap of 0.3 kanthal 2.4mm diameter with Japanese cotton coming out at 1ohm and its vaping great. Have had it up to 16W with no dry hits and no leaking issues, can't fault this clone at all. Well done to Gearbest for getting this particular one, I'm not sure on who the manufacturer is but this really is a high quality clone.

[jbryenton]

Quick update on mine, had to shim under the juice control as it was locking up too tight, aluminium foil worked a treat. Also, on 3 out of 4 juice holes on build deck section have been drilled fully through, one blocked solid enough to not allow a piece of 0.3mm kanthal to pass through. Hasn't cause any issues so far.