Sub tank builders please

[Deleted]

Hi will one of these work with the sub tank please just till I get used to wicking then I'll attempt to wind aswell www.dropbox.com/s/hwxq3v0hzbbfkyz/Screenshot_2015-02-22-21-51-20.png?dl=0
I'll be back in a sec with the other one can only post one at a time , I will get the kanger ones from fastech but there on holiday so won't get for some time
www.dropbox.com/s/a8vvcvifa2fvols/Screenshot_2015-02-22-21-51-36.png?dl=0
thanks which one please if it will be okay that is

[blakey]

They will work with the subtank & the subtank mini

[DiscoDes]

Are the legs long enough?

[Deleted]

Feb 22, 2015 22:01:15 GMT blakey said:

They will work with the subtank & the subtank mini

Thank you should I go for the six loop or seven please, I think on the guide they use six

[Deleted]

Feb 22, 2015 22:03:11 GMT DiscoDes said:

Are the legs long enough?

Lead wires of 15mm if that is what you mean ???

[whiteshep]

Legs should be long enough for the rba section look at getting a coil jig from fasttech yap only a couple of quid and useful if you've not been doing coils long . Got a 1.8 sitting in my subtank rba and getting lovely flavour and vape out of it.

[DiscoDes]

Feb 22, 2015 22:13:20 GMT @yavape said:

Feb 22, 2015 22:03:11 GMT DiscoDes said:

Are the legs long enough?

Lead wires of 15mm if that is what you mean ???

Yes, I mean are they long enough to poke out through the bottom to make the connections?

[blakey]

Feb 22, 2015 22:17:17 GMT DiscoDes said:

Feb 22, 2015 22:13:20 GMT @yavape said:

Lead wires of 15mm if that is what you mean ???

Yes, I mean are they long enough to poke out through the bottom to make the connections?

The subtank has a rebuildable section des. The legs are fine length wise for that.
No good for the rebuilding the stock attie though if that was what was meant

[blakey]

Feb 22, 2015 22:10:36 GMT @yavape said:

Feb 22, 2015 22:01:15 GMT blakey said:

They will work with the subtank & the subtank mini

Thank you should I go for the six loop or seven please, I think on the guide they use six

6 or 7 will be fine - it's the overall resistance you need to be looking at with these coils.
Both will fit, Personally I would use the 7 loops.
When I wrap coils for the subtank I wrap 7 1/2 coils around a 2mm former using .3 kanthal for a resistance of 1.3-1.4ohms.

[Deleted]

Feb 22, 2015 22:24:43 GMT blakey said:

Feb 22, 2015 22:10:36 GMT @yavape said:

Thank you should I go for the six loop or seven please, I think on the guide they use six

6 or 7 will be fine - it's the overall resistance you need to be looking at with these coils.
Both will fit, Personally I would use the 7 loops.
When I wrap coils for the subtank I wrap 7 1/2 coils around a 2mm former using .3 kanthal for a resistance of 1.3-1.4ohms.

Thank you I'm going to get used to getting the wicking right then I'll have a go at winding

[Deleted]

Feb 22, 2015 22:13:55 GMT whiteshep said:

Legs should be long enough for the rba section look at getting a coil jig from fasttech yap only a couple of quid and useful if you've not been doing coils long . Got a 1.8 sitting in my subtank rba and getting lovely flavour and vape out of it.

That's good to know because I am getting the kanger coils from fastech and there 1.5 or around that maybe a little lower but 1. Something its just there shut at the moment so will grab these till then
1.2 ohms just checked

Actually just looked they do the same coil at 1.3 ohms on eBay so I'll leave the 0.5 ohms and get the 1.3 ohms then there won't be much difference when I get the ones from fastech at 1,2 ohms

[Bluefish]

I just removed the wick dry burned and fitted new wick, coil should last for ages, and ages, and ages...

[whiteshep]

Wicking a kayfun type deck like the sub tanks rba section is easier then some make it out, just get your cotton tear\cut into strip thread through the coil if you get too much resistance take some cotton off needs to be firm but movable back and forth through the coil without affecting the coil. On the build deck you'll notice a ledge where the juice channels are use a knife or something similar to press cotton in to the corner of the ledge and cut where the mark is you want the cotton sitting on the juice channels not in them. Prime the wick with some liquid give it enough to saturate the wick even through the coil and screw on chimney section fill the tank if your confident on your priming off you go if not let it sit for fifteen minutes and then go. Been doing it this way since I started with tanks never had leakage or gurgling just nice smooth vape .

[Deleted]

Feb 23, 2015 1:57:21 GMT whiteshep said:

Wicking a kayfun type deck like the sub tanks rba section is easier then some make it out, just get your cotton tear\cut into strip thread through the coil if you get too much resistance take some cotton off needs to be firm but movable back and forth through the coil without affecting the coil. On the build deck you'll notice a ledge where the juice channels are use a knife or something similar to press cotton in to the corner of the ledge and cut where the mark is you want the cotton sitting on the juice channels not in them. Prime the wick with some liquid give it enough to saturate the wick even through the coil and screw on chimney section fill the tank if your confident on your priming off you go if not let it sit for fifteen minutes and then go. Been doing it this way since I started with tanks never had leakage or gurgling just nice smooth vape .

Brilliant this all great to know I've got such a busy week next week building the sub tank mini and rewicking the nature vape coil I'll be so happy when I've done my first one and it works though if it doesn't I shall try again till it does , I love my Atlantis but the coils are so expensive nv have brought out a new coil to fit the smok vtc sub ohm tank , I wonder if the smok coil would fit in the Atlantis as that would save me loads if not I may try and swap my Atlantis for the smok
Thank you for all the help I shall be a dab hand if a month or so with all tips

[whiteshep]

Last bit of help\advice or annoyance lol if it works doesn't have to look pretty some of my early coils were true horrors to behold but they worked .