glen
Super Member
Joined:April 2015
Posts: 5,492 
Location:
Likes: 4,501
Recent Posts
Last Online Jun 7, 2022 12:30:56 GMT
|
Post by glen on Jun 3, 2015 18:17:03 GMT
Just about to go to the shed and try to make a bit of twisted nickel
If I am not back on the forum within half an hour
Could you please ring 999 lol
|
|
pipeman01
Super Member
Joined:April 2015
Posts: 713
Location:
Likes: 678
Recent Posts
Last Online May 7, 2023 21:40:10 GMT
|
Post by pipeman01 on Jun 3, 2015 18:22:41 GMT
so the call is.... "there's a bloke called Glen, ex-postie with a fading suntan in a shed in Portsmoth......"  |
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 28, 2024 9:46:23 GMT
|
Post by Deleted on Jun 3, 2015 18:26:47 GMT
|
|
glen
Super Member
Joined:April 2015
Posts: 5,492
Location:
Likes: 4,501
Recent Posts
Last Online Jun 7, 2022 12:30:56 GMT
|
Post by glen on Jun 3, 2015 18:31:25 GMT
Well that was easier than I thought lol
Two lengths of 28gauge nickel
One end in vice
The other attached to drill
Low speed away you go
Works a treat
Thanks to everybody in previous threads for their advice
|
|
glen
Super Member
Joined:April 2015
Posts: 5,492
Location:
Likes: 4,501
Recent Posts
Last Online Jun 7, 2022 12:30:56 GMT
|
Post by glen on Jun 3, 2015 18:38:47 GMT
 Fruits of my labours lol |
|
teethcv
Super Member
Steeping Guru
Joined:February 2014
Posts: 2,412
Location:
Likes: 1,205
Recent Posts
Last Online May 16, 2022 9:43:44 GMT
|
Post by teethcv on Jun 3, 2015 18:42:57 GMT
Well that was easier than I thought lol Two lengths of 28gauge nickel One end in vice The other attached to drill Low speed away you go Works a treat Thanks to everybody in previous threads for their advice How many what's and what mm? |
|
glen
Super Member
Joined:April 2015
Posts: 5,492
Location:
Likes: 4,501
Recent Posts
Last Online Jun 7, 2022 12:30:56 GMT
|
Post by glen on Jun 3, 2015 18:48:06 GMT
28gauge nickel teethcv, Cut two one metre lengths Put them together One end in a smal vice The other wrapped around an old allan key in the drill Pulled tight and used drill on its slowest speed Gradually increased speed until wire broke at the end The image above is the end result |
|
teethcv
Super Member
Steeping Guru
Joined:February 2014
Posts: 2,412
Location:
Likes: 1,205
Recent Posts
Last Online May 16, 2022 9:43:44 GMT
|
Post by teethcv on Jun 3, 2015 18:50:06 GMT
28gauge nickel teethcv, Cut two one metre lengths Put them together One end in a smal vice The other wrapped around an old allan key in the drill Pulled tight and used drill on its slowest speed Gradually increased speed until wire broke at the end The image above is the end result Yea I know this part lol i mean to to make the coil how many whaps at what mm 2.5 3 |
|
glen
Super Member
Joined:April 2015
Posts: 5,492
Location:
Likes: 4,501
Recent Posts
Last Online Jun 7, 2022 12:30:56 GMT
|
Post by glen on Jun 3, 2015 18:52:03 GMT
Not got a clue teethcv lol I haven't got that far yet Small steps and all that |
|
teethcv
Super Member
Steeping Guru
Joined:February 2014
Posts: 2,412
Location:
Likes: 1,205
Recent Posts
Last Online May 16, 2022 9:43:44 GMT
|
Post by teethcv on Jun 3, 2015 18:53:30 GMT
Not got a clue teethcv lol I haven't got that far yet Small steps and all that By what I just worked out you will need 17 whaps just to her 0.12 lol that's at 3mm |
|
glen
Super Member
Joined:April 2015
Posts: 5,492
Location:
Likes: 4,501
Recent Posts
Last Online Jun 7, 2022 12:30:56 GMT
|
Post by glen on Jun 3, 2015 18:57:13 GMT
Not got aata clue teethcv lol I haven't got that far yet Small steps and all that By what I just worked out you will need 17 whaps just to her 0.12 lol that's at 3mm I would have thought doubling the thickness of the wire would result in needing less wraps at the moment using single 28gauge 12 wraps on 2.5mm gives me around 0.20hms |
|
|
|
Post by goneforagasper on Jun 3, 2015 18:58:05 GMT
A fine example @tedster we can all learn from this - what is the resistance ?
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 28, 2024 9:46:23 GMT
|
Post by Deleted on Jun 3, 2015 19:02:17 GMT
A fine example @tedster we can all learn from this - what is the resistance ? I'd guess 00.01  . Dunno I found the pic online  |
|
glen
Super Member
Joined:April 2015
Posts: 5,492
Location:
Likes: 4,501
Recent Posts
Last Online Jun 7, 2022 12:30:56 GMT
|
Post by glen on Jun 3, 2015 19:04:16 GMT
My first dual coil attempt looked a bit like that by the time I finished with it lol
|
|
teethcv
Super Member
Steeping Guru
Joined:February 2014
Posts: 2,412
Location:
Likes: 1,205
Recent Posts
Last Online May 16, 2022 9:43:44 GMT
|
Post by teethcv on Jun 4, 2015 5:49:57 GMT
By what I just worked out you will need 17 whaps just to her 0.12 lol that's at 3mm I would have thought doubling the thickness of the wire would result in needing less wraps at the moment using single 28gauge 12 wraps on 2.5mm gives me around 0.20hms But the lowers the wire the less ohms so you should twist 30g then I will be 28 because you twist 28 makes it 26 then you will need 17 whatpsx I might be wrong but I don't think I am |
|
. Dunno I found the pic online 