squonking tubing?

[frew]

Hello!

Can anyone recommend where I can pick up some tubing? don't need much...just received a flask squonker and the tube's too short so the bottom of the bottle sits right in the middle of the hole.

Thanks

Frew

[phatfil]

cant help with a link to silicone tube but can suggest an alternative, my new squonking mod focalecig.com/Product/Authentic-S-CA3-18650-50W-Variable-Wattage-VW-Box-Mod-with-Rebuildable-Dripping-AtomizerBlack-29166 uses a hollow SS needle to puncture the bottle nipple and reach the bottle bottom, find the right guage tube/needle for a snug fit into your existing silicone tube and you may find you have plenty already??

sorry no pics of the bottle and SS tube in the ad..

[Deleted]

link

[Pepperty]

I bought from eBay. It was food grade silicon hose tubing. It can be bought by the metre, I paid a couple of pounds. The hard part is finding the correct tube wall thickness and inner circumference for your need

[frew]

Thanks phatfil had a look at the before settling on the flask, but can't be doing with the fire button position.

@windows that's spot on, thanks.

[frew]

Thanks Pepperty I'll have a look and compare with @windows link.

[phatfil]

fwiw frew the fire button sits under the thumb for a comfy/easy fire..

[ginge7289]

Sept 2, 2015 18:09:20 GMT @windows said:

link

I ordered from these last Wednesday, still not arrived.

[Deleted]

I ordered 100 quids worth of gear from a vendor that got lost by royal fail, that's life.

[ginge7289]

I'm after some help. I finally managed to get hold of some 2mm ID/4mm OD tubing, however it is to thin to fit in a standard Svap bottle. I have a spare bottle but it does not have the same top as the Svap bottle. Are people drilling the lids of the bottles to push the tube through? If so are you drilling them to 4mm or slightly smaller for a tighter fix?

[gaz0012]

www.svapiamo.com/fai-da-te-x-boxmod/362-tubo-2x5-mm.html?search_query=Tubo&results=2

[ginge7289]

Sept 10, 2015 16:23:08 GMT gaz0012 said:

www.svapiamo.com/fai-da-te-x-boxmod/362-tubo-2x5-mm.html?search_query=Tubo&results=2

I have seen this, I was trying to avoid ordering from Italy and I read that a few people have said to use 2 x 4mm tubing, including @windows with his link above.

That tubing from Svap fits perfectly in the bottles they supply, but I'm sure a lot of people use other bottles? Well I guess they do?

I have very little knowledge on Squonking so any advice is more than welcomed.

[chrisjw]

Sept 2, 2015 18:09:20 GMT @windows said:

link

Handy link that @windows...........Thanks............




"Life...........is just a bowl of tricks!!!!!!"

[stej]

Sept 10, 2015 15:06:17 GMT ginge7289 said:

I'm after some help. I finally managed to get hold of some 2mm ID/4mm OD tubing, however it is to thin to fit in a standard Svap bottle. I have a spare bottle but it does not have the same top as the Svap bottle. Are people drilling the lids of the bottles to push the tube through? If so are you drilling them to 4mm or slightly smaller for a tighter fix?

I managed to find a couple of tips that fit my bottles. These can be sliced at the top and then drilled with a 2mm drill to get the hole started then opened up with a 4mm
The tube then pushes through nice and tight. You can use hot glue if needed or epoxy to seal it if needed but i found that if you get the slice just right then the drill at 4mm will give a good enough seal









Using these bottles on my windows squonker and the new fat daddy v5 which has a 3mm OD BF pin. The tube needs opening with a 3mm drill bit at first but then its easy enough to attach after and stays nice and secure

[ginge7289]

That's great, cheers stej