Dna200

[flavourtank]

Sept 8, 2015 21:55:19 GMT VapingBad said:

Also look at the analyser as you tighten & loosen the atty, some atties don't like too much pressure from the spring.

just praised out the 510 pin a bit on atty and screwed back on and seems told hold at mo on 0.24ohms but ain't holding my breath that it will stay lol

[flavourtank]

Sept 8, 2015 22:08:47 GMT VapingBad said:

Sept 8, 2015 22:05:22 GMT flavourtank said:

spring in 510 works fine, the coil connections are fine

It's got to be something with the atty not connecting to 510 pin properly

It's a subtank mini

Do you have any Ni200 you can bung in a dripper or something you can try, I have seen a lot of complaints with sub-tank Ni heads and IIRC they don't like to be tightened down too much.

I'm using the rba head

[glen]

Sept 8, 2015 22:08:47 GMT VapingBad said:

Sept 8, 2015 22:05:22 GMT flavourtank said:

spring in 510 works fine, the coil connections are fine

It's got to be something with the atty not connecting to 510 pin properly

It's a subtank mini

Do you have any Ni200 you can bung in a dripper or something you can try, I have seen a lot of complaints with sub-tank Ni heads and IIRC they don't like to be tightened down too much.



When used the subtank if was with the rebuildable deck, never used a stock head and as I said earlier the ohms didn't jump

[VapingBad]

May just be a slightly shorter pin than the 510 likes on that, no standard length is a problem.

[flavourtank]

Sept 8, 2015 22:14:30 GMT VapingBad said:

May just be a slightly shorter pin than the 510 likes on that, no standard length is a problem.

ohms are ranging now from 0.15-0.19

It's worse than the Mrs can't make it's mind up

[flavourtank]

Sod it stupid thing,

Try again tomorrow

It will not beat me

[glen]

Sept 8, 2015 22:24:05 GMT flavourtank said:

Sept 8, 2015 22:14:30 GMT VapingBad said:

May just be a slightly shorter pin than the 510 likes on that, no standard length is a problem.

ohms are ranging now from 0.15-0.19

It's worse than the Mrs can't make it's mind up

Is that with the ohms locked mate

[VapingBad]

Sept 8, 2015 22:24:05 GMT flavourtank said:

Sept 8, 2015 22:14:30 GMT VapingBad said:

May just be a slightly shorter pin than the 510 likes on that, no standard length is a problem.

ohms are ranging now from 0.15-0.19

It's worse than the Mrs can't make it's mind up

A lot better, but still Pete Tong. Just try different pressures screwing it onto the mod you want decent pressure from the spring, clean the connections, re-check the coil screws.  If all that fails check the insulator in the 510 has not loosened or damaged, IIRC it is a FD 510.  It may just be that tank, would be best to try something simple like a dripper that makes a good connection.

[flavourtank]

Sept 8, 2015 22:29:57 GMT glen said:

Sept 8, 2015 22:24:05 GMT flavourtank said:

ohms are ranging now from 0.15-0.19

It's worse than the Mrs can't make it's mind up

Is that with the ohms locked mate

nope, might try it locked tomorrow

[VapingBad]

Sept 8, 2015 22:29:57 GMT glen said:

Sept 8, 2015 22:24:05 GMT flavourtank said:

ohms are ranging now from 0.15-0.19

It's worse than the Mrs can't make it's mind up

Is that with the ohms locked mate

Ohm lock is only for the the Cold Ohms, the Raw Ohms will still be live, the ohms on the DNA screen should not change unless it has selected non-temp-limited mode which is possible with an inconstant connection.

[flavourtank]

Sept 8, 2015 22:32:16 GMT VapingBad said:

Sept 8, 2015 22:24:05 GMT flavourtank said:

ohms are ranging now from 0.15-0.19

It's worse than the Mrs can't make it's mind up

A lot better, but still Pete Tong. Just try different pressures screwing it onto the mod you want decent pressure from the spring, clean the connections, re-check the coil screws.  If all that fails check the insulator in the 510 has not loosened or damaged, IIRC it is a FD 510.  It may just be that tank, would be best to try something simple like a dripper that makes a good connection.

I'll look at it tomorrow, just never had a problem on other mods. But then this is technical mod lol

[VapingBad]

Sept 8, 2015 22:34:52 GMT flavourtank said:

Sept 8, 2015 22:32:16 GMT VapingBad said:

A lot better, but still Pete Tong. Just try different pressures screwing it onto the mod you want decent pressure from the spring, clean the connections, re-check the coil screws.  If all that fails check the insulator in the 510 has not loosened or damaged, IIRC it is a FD 510.  It may just be that tank, would be best to try something simple like a dripper that makes a good connection.

I'll look at it tomorrow, just never had a problem on other mods. But then this is technical mod lol

But you can't see it on most mods.   I am as sure as I can be it is the atty and/or 510, far far more likely the atty as it was fine for glen.

[decoy]

i dont get much luck with sub tanks as they dont seem to nip he thin wire to good
ive started wrapping the wire round the screws and it seems to help with the thin stuff
have got 0.4 in it at the moe with out wrapping it round the screws and its behaving
one lastthing to try is pushing the center pin of the base up a little when the coil isnt in so it pushes it back out when you refit the coil
owww and my fave fubar i did dont make the coils to big or they hi the top cap of the rda base
im haveing a lot of fun with tc and subtank as you can tell

[flavourtank]

Sept 8, 2015 22:38:27 GMT VapingBad said:

Sept 8, 2015 22:34:52 GMT flavourtank said:

I'll look at it tomorrow, just never had a problem on other mods. But then this is technical mod lol

But you can't see it on most mods.   I am as sure as I can be it is the atty and/or 510, far far more likely the atty as it was fine for glen.

I've got a feeling it's the atty being the problem, will try something else on it tomorrow, thanks for your help really appreciated

[glen]

Sept 8, 2015 22:38:27 GMT VapingBad said:

Sept 8, 2015 22:34:52 GMT flavourtank said:

I'll look at it tomorrow, just never had a problem on other mods. But then this is technical mod lol

But you can't see it on most mods.   I am as sure as I can be it is the atty and/or 510, far far more likely the atty as it was fine for glen.


I would not have sold it if I thought there was a problem with it, poor old windows would have had me bleating on about it if it was happening when I used it