best way to wick the uwell?

[peter12]

As title. Some times I get it spot in but haven't found a method that's just right yet.

[peter12]

I got it. Found its best wick it normally then cut the wick close to coils and out a small square of a pad in each end of the wick works perfect and gives a very dense vape

[flavourtank]

peter12 you got pics?

I wicked mine and then after a while I get juice in airflow area, which I then pour out, it's got to be my wicking

[mike weaver93]

flavourtank

I had the exact same issues...

However.... when I changed my wicking method to the 'Scottish Roll' , it immediately cleared up the
leaking issue.

[peter12]

flavourtank similar to Mike I found that more is better with the uwell. I used 2 methods both worked well.

Method 1 thickish amount that i then folded at the end so it was like a sandwich. Had to use a pointed tweezer to get it all in when putting rba back together.

Method 2 wick it like normal then cut the wick in both sides close to the coil. Them cut 2 small ish squares of cotton. Juice the wick then stick a square in each end of the cotton wick. Again will need ro be squeezed in a little to get the rba cap back on

[flavourtank]

peter12 mike weaver93

I've used thicker wick and watched a video where the guy s bends the ends of the wick, seems good so far leaking wise but I used the muji that came with it and it tastes bloody awful some sort of chemical taste haha so will try with rayon later

Thanks chaps

[peter12]

Oct 19, 2015 9:10:20 GMT flavourtank said:

peter12 mike weaver93

I've used thicker wick and watched a video where the guy s bends the ends of the wick, seems good so far leaking wise but I used the muji that came with it and it tastes bloody awful some sort of chemical taste haha so will try with rayon later

Thanks chaps

Did you try the other method? Were you place to squares of muji at each end of the wick?

[flavourtank]

Oct 19, 2015 9:27:58 GMT peter12 said:

Oct 19, 2015 9:10:20 GMT flavourtank said:

peter12 mike weaver93

I've used thicker wick and watched a video where the guy s bends the ends of the wick, seems good so far leaking wise but I used the muji that came with it and it tastes bloody awful some sort of chemical taste haha so will try with rayon later

Thanks chaps

Did you try the other method? Were you place to squares of muji at each end of the wick?

not yet, will give this some time then try the other if no luck

[Deleted]

Step 1 : grab a coffee ... Step 2 : Prepare yourself with a bit of Patience .... Step 3 : not so bad to have a small brandy on your side .... we finished with important things , what i missed ??? ...a..lol to show you the light ... ) ...













...tips and tricks : 1.) fill up the tank from bottom when use RBA section not from top 2.) Don't block wicking channels , cotton have to be there but don't push the cotton from the top. 3.) Using too much cotton result in bad wicking and dry hits , same happened with longer wick ... 4.) First part of cotton pad i peeled 2nd is still there , i roll a little bit the cotton but not thick .

[flavourtank]

Cheers @chris2005, it's currently drowning in the cleaner

[Deleted]

i forgot to mention i don't use any tools to push the cotton , actually i don't even touch the cotton , i only trim to have the size from 2nd picture .... i have no licking , no dry hits and because of small size of cotton the time to wait until i start to vape is around 5 min only .... the more cotton you use (thick size) the longer is the time to wait .

[mosop]

Vaping with vic about 12 mins into vid