Help - Does Such A Tank Exist??

[GunJack]

I'm after a dinky tank with the following characteristics, but struggling to find one Anyone got any ideas?


1. uses kanger protank single or dual-coil type heads
2. smaller than 60mm tall
3. 510 preferable, but ego thread acceptable
4. built-in airflow controller if possible

I did try a vamo one (ego one clone) but didn't get on with it (only 0.5/1ohm heads available), shame as was great size-wise at 52mm including afc and drip-tip... closest I've got to so far is an EMOW at 63mm, but ideally shorter...

Any suggestions welcomed, TIA

[snow]

Does the 60mm have to include the drip tip GunJack ? My protanks are all around the 50mm mark with a v2 afc which is itself 10mm but without the drip tip, and you could just get a stubby drip tip to keep it under the 60mm size.

[GunJack]

Nov 5, 2015 12:33:56 GMT snow said:

Does the 60mm have to include the drip tip GunJack ? My protanks are all around the 50mm mark with a v2 afc which is itself 10mm but without the drip tip, and you could just get a stubby drip tip to keep it under the 60mm size.

that would be my last resort snow - have a couple of drip-tips in ft basket just in case...

[johnstrangey]

Airotank mega or mini maybe

[GunJack]

Nov 5, 2015 13:30:06 GMT johnstrangey said:

Airotank mega or mini maybe

the mega might be worth a closer look, only 63mm......less with a shorter drip-tip......

[johnstrangey]

I do keep going back to the mega when I've got long car journeys so I don't have to drip and drive

[GunJack]

Nov 5, 2015 14:23:39 GMT GunJack said:

Nov 5, 2015 13:30:06 GMT johnstrangey said:

Airotank mega or mini maybe

the mega might be worth a closer look, only 63mm......less with a shorter drip-tip......

hmm.... conflicting reported measurements on the size of the mega, from 63mm to 71.2mm..

anyone who's got one, any chance you could measure from the bottom edge of the base to the highest point of the drip-tip mounting hole please (ignoring the 510 thread and drip-tip itself)??

[GunJack]

Nov 5, 2015 12:33:56 GMT snow said:

Does the 60mm have to include the drip tip GunJack ? My protanks are all around the 50mm mark with a v2 afc which is itself 10mm but without the drip tip, and you could just get a stubby drip tip to keep it under the 60mm size.

looks like this is going to be my best bet... PT-2 with v1 afc and the stubby d-t I found on ft comes in at 60mm, could get 4mm shorter but that's with a stupidly-wide bore dt which I don't like....the mod I want it for is only 56mm tall

[prr]

I make the aerotank mega 43mm ignoring 510 and driptip GunJack

[blakey]

Nov 5, 2015 14:26:32 GMT johnstrangey said:

I do keep going back to the mega when I've got long car journeys so I don't have to drip and drive

You need an EZdripper

[phtumshk]

Like the Look of that vamo one tank, new 1 on me may have to get 1.
Dosent the Vamo one tank take CLR heads?

That said Im using the wismec amor tank that  uses the ego one or CLR heads.
I recoil my clr heads at 1.2ohms same as my Kfuns.

[GunJack]

Nov 5, 2015 18:05:33 GMT blakey said:

Nov 5, 2015 14:26:32 GMT johnstrangey said:

I do keep going back to the mega when I've got long car journeys so I don't have to drip and drive

You need an EZdripper

no blakey I do NOT need a dripper, way too messy and not kanger heads

..but thanks anyway

[GunJack]

Nov 5, 2015 15:35:20 GMT prr said:

I make the aerotank mega 43mm ignoring 510 and driptip GunJack

Paul you may be my new best friend Is the mega a standard 510 drip-tip? if so, I could get the tank & d-t in at about... 55mm

fasttech have 2 clones of the mega.... anyone tried either of them??

[prr]

wonder why GunJack

[blakey]

Nov 5, 2015 20:44:53 GMT GunJack said:

Nov 5, 2015 18:05:33 GMT blakey said:

You need an EZdripper

no blakey I do NOT need a dripper, way too messy and not kanger heads

..but thanks anyway

I know that, that's why I quoted the person I was referring to