ohms reading

[VapingBad]

Dec 7, 2015 18:27:26 GMT jh said:

Dec 7, 2015 16:06:58 GMT VapingBad said:

It is probably the ground screw inside near the 510, take it out, clean it and clean the hole with a pipe cleaner or dental gap brush and IPA and reassemble. If the screw is not a dome head replace it with a dome head or put a washer between it and the ground ring.

dont really know about taking things apart
i just tried a uwell crown pre made coil it is the ni200 0.15 coil
put it in the dna 40 and it is reading 0.20
brand new mod and brand new tank and coil

This is the screw, you may be able to get it out and cleaned with out even taking off the plastic cover, the insides will be a little different in the pic as it is one I built.

[jh]

Dec 7, 2015 18:58:18 GMT VapingBad said:

Dec 7, 2015 18:27:26 GMT jh said:

dont really know about taking things apart
i just tried a uwell crown pre made coil it is the ni200 0.15 coil
put it in the dna 40 and it is reading 0.20
brand new mod and brand new tank and coil

This is the screw, you may be able to get it out and cleaned with out even taking off the plastic cover, the insides will be a little different in the pic as it is one I built.

i tried to get into the back of it and cant get to it
it is the hana one mod the mod that separates
when i am lifting off the back panel and trying take from body the screen is joined to it and coming out with it
oh well thanks for all your help
james

[VapingBad]

Sorry jh I got the wrong Hana that is a V3, as robby said dirty connections including the battery connections can cause it or poor soldering. Difficult to tell over the www which mod is the more accurate, but I would expect the if the DNA is over reading by 0.04 ohm that you will get a very very hot vape and have to turn it down to something around 300 F or even less to be vapable. If you just added 0.04 ohm then when set to 400 F it would give about 550 F from a 0.1 ohm coil.

[jh]

Dec 7, 2015 19:32:55 GMT VapingBad said:

Sorry jh I got the wrong Hana that is a V3, as robby said dirty connections including the battery connections can cause it or poor soldering. Difficult to tell over the www which mod is the more accurate, but I would expect the if the DNA is over reading by 0.04 ohm that you will get a very very hot vape and have to turn it down to something around 300 F or even less to be vapable. If you just added 0.04 ohm then when set to 400 F it would give about 550 F from a 0.1 ohm coil.

yeah i have noticed the vape is hotter than on my sx mini with the same tank
well thanks for helping me out. got a dna 200 coming soon, hope that isnt the same!
james

[VapingBad]

Dec 7, 2015 19:47:05 GMT jh said:

Dec 7, 2015 19:32:55 GMT VapingBad said:

Sorry jh I got the wrong Hana that is a V3, as robby said dirty connections including the battery connections can cause it or poor soldering. Difficult to tell over the www which mod is the more accurate, but I would expect the if the DNA is over reading by 0.04 ohm that you will get a very very hot vape and have to turn it down to something around 300 F or even less to be vapable. If you just added 0.04 ohm then when set to 400 F it would give about 550 F from a 0.1 ohm coil.

yeah i have noticed the vape is hotter than on my sx mini with the same tank
well thanks for helping me out. got a dna 200 coming soon, hope that isnt the same!
james

With the DNA200 you can measure your mod resistance and put a permanent adjustment into the mod so will be to most accurate available.   I reckon there is something wrong with 510 on your Hana, probably between the negative and the body they seem to like press fit 510s, before temp limiting it wouldn't have mattered much.