My Tank wont screw in :( advice needed please

[sealover1]

Hi guys I have this tank in the photo which is a standard 510 thread 

I have been using the corsa on the right and it still is working fine but took the tank off last night to refill it and it unscrewed the tank off, it does that sometimes but this time it wont screw back in and do up its like the thread has gone but I cant see how could of happened, the tank does screw into the Istick next to it though and that works fine but I would like to keep to my corsa.

can the part the tank screws into be replaced? or swopped over as they do look the same size on both mods?  
.
.
.

[VapingBad]

If the tank has a screw slot in the centre of the 510 try tightening it, if not try a few taps on a hard surface as this sticking out to far could cause your problem. Also give the threads a good wipe with some tissue, with Isopropyl Alcohol or meths if you have any. Another thing could be the centre post on the mod is too high or stuck, but probably not if you have tried two.

[sealover1]

nope tried that no good the thread on the tank is fine as it screws in find on my other mods, can the screw in parts be swapped over? I did getting uit undone but cant seem to budge it think there must be a way of undoing them somehow though

[VapingBad]

Probably not as the outer thread is machined in the body, it sounds like the centre pin has jammed can you push it down with a rod, medium sizes allen key or similar?

[sealover1]

does anyone know where I can buy another tank the same as this one in the photo the refills says Aspire Atlantis and it also says Halo in the tank, I have the 5ml extension on this one 

[sealover1]

Mar 30, 2020 10:29:09 GMT VapingBad said:

Probably not as the outer thread is machined in the body, it sounds like the centre pin has jammed can you push it down with a rod, medium sizes allen key or similar?

do you mean the centre pin on the tank or in the mod?

[VapingBad]

Mar 30, 2020 11:36:40 GMT sealover1 said:

Mar 30, 2020 10:29:09 GMT VapingBad said:

Probably not as the outer thread is machined in the body, it sounds like the centre pin has jammed can you push it down with a rod, medium sizes allen key or similar?

do you mean the centre pin on the tank or in the mod?

On the mod, the spring mechanism can stick with dirt.

[sealover1]

No that never helped its bit mad as my other 510 2ml tank screws in fine and my halo 5ml tank screws into a different mod but not the Corsa...

[solac77]

What about putting some tape round the thread so it bites...if it get stuck out some cloth paper towel anything really and try using pliers or my new fave nut crackers

[sealover1]

I tried using some plumbers tape but never worked, what I dont get is that my other tank does up no problem

[phtumshk]

try putting the tank in the hole and whilst appplying the lightest of touches rotate the tank anti clock wise until (with any luck) you feel it drop in to the threads.
Then whilst retaining pressure try screwing it in proper.

good luck.

[charliehorse]

You could try a heat sink sealover1 - It screws into the mod and then you screw your tank into the top of it. Cheap enough to try even if it doesnt work.

Here is a link to one so you get the gist

Example Heat Sink

[sealover1]

That's good idea just bought one thanks mate

Apr 1, 2020 9:27:24 GMT charliehorse said:

You could try a heat sink sealover1 - It screws into the mod and then you screw your tank into the top of it. Cheap enough to try even if it doesnt work.

Here is a link to one so you get the gist

Example Heat Sink