domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Aug 30, 2016 19:11:30 GMT
PMed Re: Pico
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Aug 24, 2016 10:23:30 GMT
I'm withdrawing this from sale. I found a mod it sits nicely on. I'd seen reviews that were talking about 60-80watts 'to get the best from it' - but dual, 24g, 8 wraps, 3mm and it loves 32.5 watts, and is - weirdly - a relaxing, direct lung vape...
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Aug 22, 2016 22:51:24 GMT
[Completed] Thought this would make a good, large capacity, restricted lung vape. It does, but I have Aromamizers for that, so this is wasted on me. Struggling to find a mod that can take a 25mm atomiser. Has the smoothest, largest airflow and easiest wicking of all of this type of tank I've tried. This is the version with dual air holes and wick channels, rather than four. All spares unused, no replacement tank. RRP: £25-30 depending on where you look. Hard to find it in stock. Looking for £20 inc. Royal Mail 2nd class signed. PayPal G&S
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Aug 13, 2016 21:14:07 GMT
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Aug 2, 2016 13:59:14 GMT
Actually I use cotton in the Origen. I found I had to keep it upright with mesh to stop it leaking. With cotton in there it's fine...
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Aug 2, 2016 12:57:26 GMT
What about the Origen Dripper V3. I have a Tobeco V2, I also have a squonk pin I don't use. I rate it as perhaps the best MTL dripper there is. I've heard of the NarDa clone being modified for squonking too...
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Jul 29, 2016 22:38:31 GMT
Just noticed to said Cloupor, not Koopor...
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Jul 28, 2016 8:40:34 GMT
There's been some discussion on one of the other forums about the bottom o ring below the build deck preventing the tank from screwing all the way down. The juice shut off should work without any o rings. So the test was to remove the lower o ring - attach the tank and screw it down all the way - then fill and leave the top cap off. Shouldn't leak in this state. If it does then there is a machining error in the threads.
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Jul 27, 2016 8:31:43 GMT
I've got 4 Koopor Minis. All with upgraded firmware. One has a slightly scratched case. PM me, we can talk.
Fasttech do a few clone boards that might fit.
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Jul 27, 2016 8:25:32 GMT
I've got one, what's niggling you?
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Jul 22, 2016 18:38:57 GMT
Should be us giving John an extra 20%, not him knocking it off.
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Jun 23, 2016 7:16:23 GMT
Been following this thread with interest. Haven't tried the original, but vaping my own version. I'm enjoying a bit of Cola in mine...
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on Jun 23, 2016 7:13:28 GMT
I just bought 2 of these (Tobecos) - one built up with cotton, dual 3mm, 26g, 8 wraps. One with mesh 3.5mm, 26g, 8 wrap. Tried a few different builds but I like using tobaccos and coffees on a big mesh wick, like my Le Zephyr.
Amazing vape! Perfect for me. MTL, or Restricted DTL
Only tanks I need. Got a lot of other things to sell now...
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on May 30, 2016 11:49:51 GMT
No. It's not under pressure. I fill the bottles with CO2, then that gets displaced as the Nic goes in...
|
|
domejunky
Full Member
Joined:March 2016
Posts: 244
Location:
Likes: 140
Recent Posts
Last Online Apr 24, 2022 7:37:37 GMT
|
Post by domejunky on May 29, 2016 23:27:53 GMT
I've been using CO2 - putting the Nic in Belgian beer bottles with oxygen scavenging bottle caps. I brew beer, so just treated it like beer...
|
|