IGO-L

[maccafan]

I was taken in so much by the AGA-S that I hardly tried the IGO-L..

Anyone else tried theirs? How are they finding it..I will wick it this afternoon cause I have a pending juice tasting session of the samples I received from Royal Vapor which I have been putting off.

[OneDay]

Macca it's very easy to coil as there's no mini holes to poke wire through, you just put it under the screws and tighten down. The fact that the top isn't screwed means the airhole can be aligned nicely. It vapes very well - similar to a RDA. The fact that the bottom is slightly 'welled' means it can hold a fair amount of juice.

For the money a brilliant dripper

[Deleted]

Looks like o-rings only keeping the top on .. how secure is it?

[OneDay]

Not very to be honest ashmal, but you quickly get used to the fact that to screw in on and off a battery you grip the base plate not the cone. Once on a device it stays on fine.

[Deleted]

thanks - have been looking at this for my first foray into the rebuildable world although for some reason I want to try a mesh system out first rather than wicks ... probably because I'm expecting wicks to be similar to the vivi tanks I am using

[Sandra (aka Chillax)]

I have been pondering getting one fom Vapingthings, now that Oneday says the bottom is 'welled' I think I will go ahead.

Oneday, do you have a picture of it on a mod? Want to see how it looks on something.

[OneDay]

[Sandra (aka Chillax)]

Nov 30, 2012 14:59:47 GMT OneDay said:

That looks great, just like I want it to look, big thanks Oneday me likey.

[dave]

It looks good on a Vamo too Sandra

Vapes well, the only PITA is, on mine at anyrate, the top is very loose over the O rings - they need to be a bit thicker. Unfortunately I haven't found anything suitable to replace them with yet.

[piper1]

This a great set of o rings always use them

www.ebay.co.uk/itm/419-PIECE-RIC-RUBBER-O-RING-SEALS-SET-PLUMBING-TAP-WASHER-ORING-PLUMBERS-/160764223324?pt=UK_DIY_Materials_Plumbing_MJ&hash=item256e4b5f5c

[greendollar]

The IGO-L is my first dripper , I LOVE IT , been flaffing around with the genesis atomisers but find them really hard work wether it's SS or silica wicks it's very fiddlely and results are very hit and miss .....the IGO-L has been a breeze to set up, jumped straight in with an SS wick and it worked liked a dream , tried a silica wick last night ....even better , the taste and vape has definitely been the best I've experienced so far .
Impressed I decided peruse the sites last night to try and find something similar to the IGO but there doesn't seem to be alot out there of the same ilk , lots of small drippers on the market but nothing like the IGO ,the nearest I got was the Clockworks RDA .........can anyone point me in the direction of any IGO type drippers please

[ian]

Absolutely love mine also.Once you get it on your device it is a solid workhorse,i prefer this to my RDA as it is smaller and looks nice.My coil is 1.7ohm and at 4.2v it is like vaping the very best LR306 atomiser.I honestly do wish i had ordered another couple of these,definately an absolute steal of a bargain.I think i am going to order another from vapingthings as a Xmas present for my dad.

[steve386]

Finally got to set mine up today. Fantastic little atty. It did cost quite a bit, but I think it was worth it

Posh RDA.

[apostle51]

Dec 1, 2012 9:52:53 GMT greendollar said:

The IGO-L is my first dripper , I LOVE IT , been flaffing around with the genesis atomisers but find them really hard work wether it's SS or silica wicks it's very fiddlely and results are very hit and miss .....the IGO-L has been a breeze to set up, jumped straight in with an SS wick and it worked liked a dream , tried a silica wick last night ....even better , the taste and vape has definitely been the best I've experienced so far .
Impressed I decided peruse the sites last night to try and find something similar to the IGO but there doesn't seem to be alot out there of the same ilk , lots of small drippers on the market but nothing like the IGO ,the nearest I got was the Clockworks RDA .........can anyone point me in the direction of any IGO type drippers please

you can get Igo-l from a few UK vendors if your after another

www.vapingthings.com/IGO-SS_REBUILDABLE_ATOMISER/p1311952_8181214.aspx
or
www.ivapour-elixir.co.uk/parts/rebuildable-atomisers/igo-l-atomizer.html

I think the Igo-l Is based on the SattyS, havent a clue where to get them from tho

www.ohmyvape.com/archives/1849

[Perpetua]

When I get a mo, I'll have to take a picture of the Satty & IGO side by side . . . I don't think the Satty gentleman made any more after the batch of 50 that he made.