Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 23, 2024 12:25:58 GMT
|
Post by Deleted on Jan 3, 2013 9:44:43 GMT
... guess what I am doing this morning ...
|
|
meeee
Super Member
Tis Meeee
Joined:September 2012
Posts: 1,008
Location:
Likes: 207
Recent Posts
Last Online Feb 6, 2013 22:05:18 GMT
|
Post by meeee on Jan 3, 2013 10:13:36 GMT
Lucky you, mine should be here today as well.
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 23, 2024 12:25:58 GMT
|
Post by Deleted on Jan 3, 2013 10:29:17 GMT
you'll love it ...doddle to setup
|
|
|
Post by Perpetua on Jan 3, 2013 13:11:02 GMT
What do you think so far Ash?
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 23, 2024 12:25:58 GMT
|
Post by Deleted on Jan 3, 2013 13:19:04 GMT
luverly ...my blue foam hasn't arrived yet so using sera. Easy to coil at an angle over the airhole. Running at 1.7... prefer a bit lower but erred on side of caution. Given it a run out with 555 and Griz's Peanut Butter. Smooooth ... I had a woozy head after my first few draws.
Tons of vapour. Best buy so far. Just about to setup an AGA-S ... must do some work at some point
|
|
baconandeggs
Senior Member
Joined:September 2012
Posts: 377
Location:
Likes: 105
Recent Posts
Last Online Nov 9, 2024 9:48:40 GMT
|
Post by baconandeggs on Jan 3, 2013 19:01:24 GMT
Twins
|
|
|
Post by Perpetua on Jan 3, 2013 21:18:25 GMT
* Jealous * . . . enjoy Eggie!
|
|
dognero
Senior Member
Joined:April 2012
Posts: 498
Location:
Likes: 68
Recent Posts
Last Online Nov 21, 2018 20:26:24 GMT
|
Post by dognero on Jan 3, 2013 21:30:36 GMT
Want one but will have to wait till they are back in stock and be fast
|
|
meeee
Super Member
Tis Meeee
Joined:September 2012
Posts: 1,008
Location:
Likes: 207
Recent Posts
Last Online Feb 6, 2013 22:05:18 GMT
|
Post by meeee on Jan 3, 2013 21:33:06 GMT
I was a bit disappointed with mine as it’s not that shiny so have put it back in the envelope for another day.
|
|
|
Post by Perpetua on Jan 3, 2013 22:11:27 GMT
Awwww Meeee . . . I don't go for the highly polished finish, on anything, sends my finger print OCD into meltdown. You could always give it a buff up with some Autoglym.
|
|
trish
Full Member
I don't want much.....I just want more!
Joined:July 2012
Posts: 127
Location:
Likes: 14
Recent Posts
Last Online Sept 18, 2018 12:36:09 GMT
|
Post by trish on Jan 3, 2013 22:29:43 GMT
I got mine today as well....but Iv'e got a horrible taint to the flavour. I think it's oil from the machining, because when I opened the top cap a lot of liquid came out, which smelled like oil to me. I cleaned it in hot water with a little bit of washing up liquid then I dried it and used an alcohol wipe and rinsed it again, but the taste is still there. I didn't actually submerge the base in water as I wasn't sure if that would be O.K? I'm trying to vape through it, but the oily taste has not gone away yet, after a couple of hours vaping. Anyone have any suggestions?
|
|
Deleted
Joined:January 1970
Posts: 0
Location:
Recent Posts
Last Online Nov 23, 2024 12:25:58 GMT
|
Post by Deleted on Jan 3, 2013 22:32:13 GMT
I washed mine under tap before use. I assume you have put new filler in ?
|
|
Moon
Senior Member
Joined:September 2012
Posts: 382
Location:
Likes: 22
Recent Posts
Last Online Dec 31, 2015 14:27:30 GMT
|
Post by Moon on Jan 3, 2013 22:34:59 GMT
I got mine today as well....but Iv'e got a horrible taint to the flavour. I think it's oil from the machining, because when I opened the top cap a lot of liquid came out, which smelled like oil to me. I cleaned it in hot water with a little bit of washing up liquid then I dried it and used an alcohol wipe and rinsed it again, but the taste is still there. I didn't actually submerge the base in water as I wasn't sure if that would be O.K? I'm trying to vape through it, but the oily taste has not gone away yet, after a couple of hours vaping. Anyone have any suggestions? It's stainless steel so submerging it in washing up liquid won't harm it. If that doesn't do it, isopropyl alcohol should do the job.
|
|
trish
Full Member
I don't want much.....I just want more!
Joined:July 2012
Posts: 127
Location:
Likes: 14
Recent Posts
Last Online Sept 18, 2018 12:36:09 GMT
|
Post by trish on Jan 3, 2013 22:48:33 GMT
Yes I put new filler in. I will try submerging the base in hot water and washing up liquid tomorrow. I haven't got any isopropyl, unfortunately. Thanks for your help
|
|
|
Post by Perpetua on Jan 3, 2013 22:53:09 GMT
Simmer it in some milk Trish, for about 15 minutes or put it through a few cycles of an ultrasonic jewellry cleaner if you have one . . . a lot of us had the same when we got ours on previous batches. I thought that had been resolved now.
|
|