New RBA stock @Grey Haze and Updates!!!

[Billy | GreyHaze]

Sigelei Bagua Renamed the IChing. Available now. Pictured with the Triumvirate RDA

[scaffman69]

Just ordered the 306 atty dripper sleave and the k1 rba, nice one m8 for getting the k1 back in so quick, will you be getting any snazzy tanks in for the k1 ? and also maybe the ceramic pre coiled wicks would go down a bomb ? very fair priced site and fair postage thx ill let you know how i go with them.

[Billy | GreyHaze]

Aug 13, 2013 16:32:30 GMT scaffman69 said:

Just ordered the 306 atty dripper sleave and the k1 rba, nice one m8 for getting the k1 back in so quick, will you be getting any snazzy tanks in for the k1 ? and also maybe the ceramic pre coiled wicks would go down a bomb ? very fair priced site and fair postage thx ill let you know how i go with them.

I havnt sourced any tanks as of yet, the only thing that i found works well with the K1 that is reasonably priced is the X8, more expensive non Chinese tanks is a possibility but tbh its hard to sell many of those. ceramic pre coiled wicks is a possibility i'll see what i can do.

[richo71]

Aug 14, 2013 13:23:15 GMT Billy | GreyHaze said:

Aug 13, 2013 16:32:30 GMT scaffman69 said:

Just ordered the 306 atty dripper sleave and the k1 rba, nice one m8 for getting the k1 back in so quick, will you be getting any snazzy tanks in for the k1 ? and also maybe the ceramic pre coiled wicks would go down a bomb ? very fair priced site and fair postage thx ill let you know how i go with them.

I havnt sourced any tanks as of yet, the only thing that i found works well with the K1 that is reasonably priced is the X8, more expensive non Chinese tanks is a possibility but tbh its hard to sell many of those. ceramic pre coiled wicks is a possibility i'll see what i can do.

One tank that is cheap and of good quality and gets bypassed from time to time is the AGR tank

[jeffc]

Thanks billy the wires are top notch, great service also.

[scaffman69]

Aug 14, 2013 13:23:15 GMT Billy | GreyHaze said:

Aug 13, 2013 16:32:30 GMT scaffman69 said:

Just ordered the 306 atty dripper sleave and the k1 rba, nice one m8 for getting the k1 back in so quick, will you be getting any snazzy tanks in for the k1 ? and also maybe the ceramic pre coiled wicks would go down a bomb ? very fair priced site and fair postage thx ill let you know how i go with them.

I havnt sourced any tanks as of yet, the only thing that i found works well with the K1 that is reasonably priced is the X8, more expensive non Chinese tanks is a possibility but tbh its hard to sell many of those. ceramic pre coiled wicks is a possibility i'll see what i can do.

Ok thx, keep us posted about the ceramic wicks m8, cheers bud

[scaffman69]

Aug 14, 2013 14:45:31 GMT richo71 said:

Aug 14, 2013 13:23:15 GMT Billy | GreyHaze said:

I havnt sourced any tanks as of yet, the only thing that i found works well with the K1 that is reasonably priced is the X8, more expensive non Chinese tanks is a possibility but tbh its hard to sell many of those. ceramic pre coiled wicks is a possibility i'll see what i can do.

One tank that is cheap and of good quality and gets bypassed from time to time is the AGR tank

Yes i got an AGR tank may try that and order an X8 or maybe a better one. ill see, cheers bud.

[richo71]

There is definately something a miss with my k1 rba, i have set it up ok but juice floods through the 510, the juice flow part on the bottom aint closing off properly and i have screwed it up as far as it will go, sheer waste of time and money, i have spent a good hour and half trying to stop the juice going straight through, 3ml of juice drips out of the 510 within a couple of minutes, i dont know if i have a dud but surely it not right. I am quite competent with rba's but this aint right at all

[pyr0]

I had flooding problems too until i sorted out the airflow.
When I first built it, put it into a tank and filled it, I couldn't get a draw at all and was sucking juice into the chamber (which then flooded out of the 510 connector).

I pondered about it for a few minutes and emailed Billy to see if he had tried a K1 and if he had experienced the same prob.

After sending the email I realised the silicone grommet the manufacturer had used around the 510 pin was blocking the airflow holes on the side of the 510 thread.

I unscrewed the 510 pin, pulled out the grommet, and put back the pin.

Rebuilt and refilled and it's been fine ever since.

I wrote to Billy again with the fix and he posted it on his site

I've now put a few tanks of juice through this K1 so far with no leaks, plenty of vapour and flavour too

[richo71]

Sorry flooding is the wrong word more leaking through the atty, Mine is leaking straight through when its in the tank and im just holding the tank

[pyr0]

Are you filling it with the juice control closed or hidden?
What tank are you using?

I'm only using a cheap x8 tank at the moment, but when refilling I push the K1 down in the tank so the juice control is hidden in the bottom cap. Then I open the refill screw, fill with a syringe, put the fill screw back and move the K1 back up so the juice control is exposed again.

Doing it this way makes sure I don't flood it while filling and also makes sure I don't have to adjust the juice control and fiddle with the adjustable 510 pin.

[Billy | GreyHaze]

Aug 15, 2013 14:23:02 GMT richo71 said:

There is definately something a miss with my k1 rba, i have set it up ok but juice floods through the 510, the juice flow part on the bottom aint closing off properly and i have screwed it up as far as it will go, sheer waste of time and money, i have spent a good hour and half trying to stop the juice going straight through, 3ml of juice drips out of the 510 within a couple of minutes, i dont know if i have a dud but surely it not right. I am quite competent with rba's but this aint right at all

Just to add the pin the ceramic cup sits on is also adjustable, its possibly sitting to low stopping the juice control from closing off properly.

If you feel its faulty email me and ill send you replacement parts.

[Billy | GreyHaze]

Enter code 'DISCOUNT2015' for 15% off all orders above £20.

Terminator-C Long Mod pre-orders will start this week end.

Sigelei #8w is back in stock, resistance wires will be back in stock next week.

Also apologies to any one who suffered postage delays, we were inundated with orders last week and took us a few days playing catch up to get everything out, We have updated our postage system so we hope it wont happen again.

[Edge]

Aug 16, 2013 19:16:18 GMT Billy | GreyHaze said:

Terminator-C Long Mod pre-orders will start this week end.

On sale/pre-order now.

[richo71]

Aug 16, 2013 19:16:18 GMT Billy | GreyHaze said:

Enter code 'DISCOUNT2015' for 15% off all orders above £20.

Terminator-C Long Mod pre-orders will start this week end.

Sigelei #8w is back in stock, resistance wires will be back in stock next week.

Also apologies to any one who suffered postage delays, we were inundated with orders last week and took us a few days playing catch up to get everything out, We have updated our postage system so we hope it wont happen again.

Just ordered, less than £30 delivered, bargain