New RBA stock @Grey Haze and Updates!!!

[blakey]

Aug 21, 2013 22:22:51 GMT stu1873 said:

Cheers for that bud. Forgot about the centre tube in the AGR+ tank being a problem. I do have an X8 tank I can try it in though.

Maybe a diver will work in the AGR+ tank then.

Diver works fine in that tank mate, sits a little proud due to that flange though.

[blakey]

On another note, used a few of these ready wires from grey haze and found them to be superb. Will grab a few more when they're in stock again

[richo71]

Aug 21, 2013 17:39:30 GMT stu1873 said:

Just about to pull the trigger on a K1 and Terminator C RBA from Grey Haze.

Can you tell me when the pre-made coils will be available and is there a way to apply a discount code on the shopping cart. Also can the ceramic parts of the K1 and Terminator C be bought seperatley for spares?

Cheers Stu

The K1 is a nightmare stu, and be very very careful with the ceramic cup putting it on the post, i have had spare bottom section sent to me because of constant leaking, the pins dont make contact when screwed together and reads no ohms and that ceramic cup or the post is to tight fit, to be honest dont waste your money because in my opinion maybe only 1 in 10 people will get this to work

[stu1873]

Aw man, that's not good news!

Order is in for the K1 but not had an email to say it's enroute yet.

Need a review of the Magoo before I buy but it does look promising.

[jimmy]

is there any news on when we can expect delivery of the terminator c?

[richo71]

Hi Billy, although the pre-made wires are good they are only just long enough for the magoo so i suspect they will be the same with the terminator, my question is do they do these wires with longer no res legs?

[scaffman69]

Aug 23, 2013 1:16:07 GMT richo71 said:

Aug 21, 2013 17:39:30 GMT stu1873 said:

Just about to pull the trigger on a K1 and Terminator C RBA from Grey Haze.

Can you tell me when the pre-made coils will be available and is there a way to apply a discount code on the shopping cart. Also can the ceramic parts of the K1 and Terminator C be bought seperatley for spares?

Cheers Stu

The K1 is a nightmare stu, and be very very careful with the ceramic cup putting it on the post, i have had spare bottom section sent to me because of constant leaking, the pins dont make contact when screwed together and reads no ohms and that ceramic cup or the post is to tight fit, to be honest dont waste your money because in my opinion maybe only 1 in 10 people will get this to work

Same problem here the ceramic is way too tight a fit.

[stu1873]

Aug 24, 2013 12:41:51 GMT scaffman69 said:

Aug 23, 2013 1:16:07 GMT richo71 said:

The K1 is a nightmare stu, and be very very careful with the ceramic cup putting it on the post, i have had spare bottom section sent to me because of constant leaking, the pins dont make contact when screwed together and reads no ohms and that ceramic cup or the post is to tight fit, to be honest dont waste your money because in my opinion maybe only 1 in 10 people will get this to work

Same problem here the ceramic is way too tight a fit.

Tell me about it. I broke mine last night on the first attempt to fit it with a coil on it!

[mike weaver93]

Dumb question:

Does anyone know. if the premade coils, would fit in a Phoenix and a Nimbus atty??or do they need silica wick only.

Cheers

Mike

[richo71]

Hi billy we havent heard from you as a vendor for quite some time, but seen as many have bought (inc myself) the k1 rba and broke the ceramic cup due to poor design and NOT the end users fault and we have k1's that are now garbage can fodder, when are the promised ceramic cups coming onto your webshop, to be honest these should not have been sold really as it has a fundamental design flaw and we (the consumers) have spent £££'s with you on a sub-standard rba which is not fit for purpose. We all read the many notes and disclaimers and followed the instructions on your item page which is useless if the product has design flaws (which it has) as many buyers have found out. many, many people are sitting with an rba that is useless, Please reply Billy, Regards Carl

[Billy | GreyHaze]

Aug 28, 2013 13:22:02 GMT richo71 said:

Hi billy we havent heard from you as a vendor for quite some time, but seen as many have bought (inc myself) the k1 rba and broke the ceramic cup due to poor design and NOT the end users fault and we have k1's that are now garbage can fodder, when are the promised ceramic cups coming onto your webshop, to be honest these should not have been sold really as it has a fundamental design flaw and we (the consumers) have spent £££'s with you on a sub-standard rba which is not fit for purpose. We all read the many notes and disclaimers and followed the instructions on your item page which is useless if the product has design flaws (which it has) as many buyers have found out. many, many people are sitting with an rba that is useless, Please reply Billy, Regards Carl

I do not have the ceramic cups in bulk as of yet, i should have them in stock with in the next two weeks, the reason its taking so long is because I'm working with the supplier to iron out the issues the K1 has, i don't want to get anything in only for it to cause another problem.

If any one has broken their ceramic cup, please email me at [e-mail] and i will sent you a replacement that is wider and should fit comfortably with a wire. in it.

I have also set up a blog on my site the instruction on how to set up the K1.

[Billy | GreyHaze]

Aug 23, 2013 6:42:44 GMT jimmy said:

is there any news on when we can expect delivery of the terminator c?

All have now been dispatched, you should receive tomorrow.

[Billy | GreyHaze]

Aug 23, 2013 13:15:36 GMT richo71 said:

Hi Billy, although the pre-made wires are good they are only just long enough for the magoo so i suspect they will be the same with the terminator, my question is do they do these wires with longer no res legs?

The non res legs are 4cm in length of the batch i have in stock now, longer than the initial batch, these should work comfortably with the magoo or terminator mod. I have asked for longer legs, however everything they have in stock is at 4cm they wont begin production of longer legs just yet, i will have to wait till they start production again in which case i should be able to get longer legs.

[Perpetua]

Aug 27, 2013 8:58:51 GMT mike weaver93 said:

Dumb question:

Does anyone know. if the premade coils, would fit in a Phoenix and a Nimbus atty??or do they need silica wick only.

Cheers

Mike

You only need resistance wire with both those atomisers Mike . . . the ready made wires that Billy stocks are non res/res, which isn't necessary in either of those.

This would be the wire you'd need for coil making:


greyhaze.co.uk/collections/just-arrived/products/kanthal-wire-10-meter

[mike weaver93]

Aug 28, 2013 16:04:44 GMT Perpetua said:

Aug 27, 2013 8:58:51 GMT mike weaver93 said:

Dumb question:

Does anyone know. if the premade coils, would fit in a Phoenix and a Nimbus atty??or do they need silica wick only.

Cheers

Mike

You only need resistance wire with both those atomisers Mike . . . the ready made wires that Billy stocks are non res/res, which isn't necessary in either of those.

This would be the wire you'd need for coil making:


greyhaze.co.uk/collections/just-arrived/products/kanthal-wire-10-meter

Thanks Mandy,

Coupled with the Kanthal, Would Ekowool be better than Silica? ,also what width, would I need?

Cheers

Mike