Can someone recommend me a good dct tank?

[GunJack]

timbo, yes you would

[Timbo]

Aug 8, 2013 10:56:26 GMT Super-Shiny said:

I always get these one's: www.vapeescape.co.uk/Vaping-Spares/Cartomisers/Boge-Pre-Punched-Cartomisers-5.html

They have never failed me

Shame they don't fit the AGR.

[Super-Shiny]

Aug 8, 2013 11:04:26 GMT Timbo said:

Aug 8, 2013 10:56:26 GMT Super-Shiny said:

I always get these one's: www.vapeescape.co.uk/Vaping-Spares/Cartomisers/Boge-Pre-Punched-Cartomisers-5.html

They have never failed me

Shame they don't fit the AGR.

They fitted perfect when i had my AGR ???

[Timbo]

I'm confused! The AGR fits overall 40mm or 50mm. Those Boge cartomisers are 45mm overall.

Will it still fit then?

[Super-Shiny]

Aug 8, 2013 11:16:20 GMT Timbo said:

I'm confused! The AGR fits overall 40mm or 50mm. Those Boge cartomisers are 45mm overall.

Will it still fit then?

I think they are saying for the AGR overall is not including the thread, Boge cartomisers are 40mm and 45mm without the thread.

But yes they will be fine, i used them for ages and there has been no design change for the carto's or the AGR that i can see of.

[Roscopecotrain]

Some measure both the carto and the thread and some just the carto. Super-Shiny is right they will fit with no issues.

Sent from my Galaxy Note 2

[Timbo]

Thank you all for your help. Time to get ordering!

Feeling excited! :-)

[Roscopecotrain]

Aug 8, 2013 11:49:18 GMT Timbo said:

Thank you all for your help. Time to get ordering!

Feeling excited! :-)

Enjoy

Sent from my Galaxy Note 2

[Timbo]

Ok, so I have the tank. Took me a while to figure out how to put it together. WAS A COMPLETE FAIL!!! About the same amount of vapor as you would breathing out condensation on a cold day!!

The cartomiser flooded so that must be the reason. I have taken it apart and cleaned it. I am not having a go as in its your fault by the way!!

So can anyone explain to me how to use this tank and put it together please?

Thank you.

[Super-Shiny]

Little guide i done ages ago:

For carto's i always used:
www.vapeescape.co.uk/Vaping-Spares/Cartomisers/Boge-Pre-Punched-Cartomisers-5.html

I would fill them using the condom method and leave to rest for 20-30 mins, once rested make sure there is no flooding, good idea is to vape the carto for a couple of seconds on it's own to make sure all is fine.

This applies to tanks with a filling hole at the top: If the carto is fine and good to go fit it into the tank and screw tank lid on (only fill tank with the hole provided on top of the cap).

Fill tank too around 60-70%, i prefer 60%, i tend to find the more you fill it the more chance of flooding (think it is to do with pressure).

Leave to rest in the tank for awhile to let the carto adjust to it and then try it out.

You can also before starting to use it is do the dry vaping, by blocking the bottom of the carto hole (when it's in the tank) vape until you see no more bubbles come out of the punched hole, like this video here:



Another video on tanks here:



The other reason i fill to around 60% is because IF it does feel like it is flooding you can tilt the tank and vape only the juice from the carto which will empty the extra juice in the carto, if the tank was 100% full you could not do this because there is no empty room left so it will just keep pulling in more juice from the tank.

Gotta just remember that the Carto is like a submarine in water and all that juice is wanting to get in, so when vaping with a tank it's best not to fast vape continuously as you will be pulling in loads of juice too much and too often.

Hope some of this helps.

[Perpetua]

Aug 9, 2013 16:01:51 GMT Timbo said:

So can anyone explain to me how to use this tank and put it together please?

Thank you.

Is it the AGR you bought Tim? If so this video from PBusardo may give you some pointers.

[Timbo]

Here is a picture of the bottom part with the boge attached. I am presuming the drip tip goes in the carto as there is no where else for it go.

Where does the hole on the left part pictured go? Top/Bottom?

[Super-Shiny]

Aug 9, 2013 16:18:12 GMT Timbo said:

Here is a picture of the bottom part with the boge attached. I am presuming the drip tip goes in the carto as there is no where else for it go.

Where does the hole on the left part pictured go? Top/Bottom?

The left part should go over the cartomizer and the hole on it should line up with the hole on the cartomizer, as for the drip tip put that on last once you are ready to use it.

[Super-Shiny]

I thought you was getting this one: www.vapingthings.com/AGR2_SSPOLYCARBONATE_TANK/p1311952_8774412.aspx

It seems you have this one: www.vapingthings.com/AGR+_SSPYREX_TANK/p1311952_9953290.aspx

Never used the one you have got but it looks pretty much the same apart from that carto cover.

[Timbo]

Aug 9, 2013 16:28:04 GMT Super-Shiny said:

Aug 9, 2013 16:18:12 GMT Timbo said:

Here is a picture of the bottom part with the boge attached. I am presuming the drip tip goes in the carto as there is no where else for it go.

Where does the hole on the left part pictured go? Top/Bottom?

'The left part should go over the cartomizer and the hole on it should line up with the hole on the cartomizer, as for the drip tip put that on last once you are ready to use it.'


See this is the problem When the left part is screwed in the hole is to low to match the other hole Also there is a gap on the inside, it is not flush so it just fills up, probably why it would not work.