What is your top three attys

[Village idiot formerly tjlumle]

Nov 30, 2013 8:37:06 GMT @freefromsmoking said:

Nov 30, 2013 8:29:12 GMT Village idiot formerly tjlumle said:

Shame my punching could do with some work at the min

The trick is to screw in slowly until you hear a click and then another 1/4 turn only  ....  any more and you will get flooding

1 or 2 holes?

[Deleted]

Nov 30, 2013 8:40:12 GMT Village idiot formerly tjlumle said:

Nov 30, 2013 8:37:06 GMT @freefromsmoking said:

The trick is to screw in slowly until you hear a click and then another 1/4 turn only  ....  any more and you will get flooding

1 or 2 holes?

2 holes directly opposite each other   ....  lay the carto beside your tank and mark the carto with a marker pen at the point just above where the bottom of the tank glass is and punch your holes at this level (about 2 - 3 mm above the bottom of the glass)

[xrayspecs]

Nov 29, 2013 21:11:27 GMT ginge7289 said:

1. Kayfun
2. Kayfun
3. Kayfun

Trying to like genesis, really want to try a rose.

I'd have to agree with your top three there - the Kayfun is the most satisfying and consistent atty I've owned.

[Karma]

Nov 30, 2013 8:29:12 GMT Village idiot formerly tjlumle said:

Nov 29, 2013 21:21:02 GMT @freefromsmoking said:

Definitely an often overlooked gem these days  ...  punched and filled correctly they are hard to beat 

Shame my punching could do with some work at the min

You can buy them ready punched

[ionian]

I'm yet to venture into the world of RBAs, so at the moment I have only one favourite: Protank 2. It's just the right size, it looks smart, it gives a nice clean taste and it's easily maintained.

[Village idiot formerly tjlumle]

Nov 30, 2013 10:12:40 GMT Karma said:

Nov 30, 2013 8:29:12 GMT Village idiot formerly tjlumle said:

Shame my punching could do with some work at the min

You can buy them ready punched

Might give those a go as with 2 holes was a little gurgly but might try one hole next time

[Village idiot formerly tjlumle]

Nov 30, 2013 8:48:45 GMT @freefromsmoking said:

Nov 30, 2013 8:40:12 GMT Village idiot formerly tjlumle said:

1 or 2 holes?

2 holes directly opposite each other   ....  lay the carto beside your tank and mark the carto with a marker pen at the point just above where the bottom of the tank glass is and punch your holes at this level (about 2 - 3 mm above the bottom of the glass)

Thats what I did it's a little gurgly from time to time though but no leaks thus far with the trap tank

[Deleted]

Nov 30, 2013 11:10:46 GMT Village idiot formerly tjlumle said:

Nov 30, 2013 8:48:45 GMT @freefromsmoking said:

2 holes directly opposite each other   ....  lay the carto beside your tank and mark the carto with a marker pen at the point just above where the bottom of the tank glass is and punch your holes at this level (about 2 - 3 mm above the bottom of the glass)

Thats what I did it's a little gurgly from time to time though but no leaks thus far with the trap tank

Sounds as though the punched holes are a little too large TJ or some air pressure has built up in the tank   ...  if you are sure that the holes are OK, try unscrewing the fill screw and letting any air pressure settle for about 15 seconds before replacing the screw  ... I do this each time I refill the Scuba to let any air bubbles escape.

[Super-Shiny]

Village idiot formerly tjlumle some good videos here:

This is my fave for obvious reasons

[Village idiot formerly tjlumle]

Nov 30, 2013 14:22:22 GMT Super-Shiny said:

Village idiot formerly tjlumle some good videos here:

This is my fave for obvious reasons

I can see why the top video is your fave haha

[Super-Shiny]

And something i wrote ages ago:

I would punch them 1 x 2mm hole (No bigger and No smaller), a 2mm hole should accommodate most thickness of juices.

Once the carto is punched i would fill them using the condom method and leave to rest for 20-30 mins, once rested make sure there is no flooding, good idea is to vape the carto for a couple of seconds on it's own to make sure all is fine.

1: This applies to tanks with a filling hole at the top: If the carto is fine and good to go fit it into the tank and screw tank lid on (only fill tank with the hole provided on top of the cap).

2: This applies to tanks without a filling hole at the top: If the carto is fine and good to go fit it into the tank too about 70% in so there is just enough room at the top too fill the juice into tank (Recommend to use a needle cap filler or syringe).

Fill tank too around 60-70%, i prefer 60%, i tend to find the more you fill it the more chance of flooding (think it is to do with pressure).

Leave to rest in the tank for awhile to let the carto adjust to it and then try it out.

You can also before starting to use it is do the dry vaping, by blocking the bottom of the carto hole (when it's in the tank) vape until you see no more bubbles come out of the punched hole

The other reason i fill to around 60% is because IF it does feel like it is flooding you can tilt the tank and vape only the juice from the carto which will empty the extra juice in the carto, if the tank was 100% full you could not do this because there is no empty room left so it will just keep pulling in more juice from the tank.

Gotta just remember that the Carto is like a submarine in water and all that juice is wanting to get in, so when vaping with a tank it's best not to fast vape continuously as you will be pulling in loads of juice too much and too often.

[alansi]

1. DBOX Puritank - micro coil
2. Hyper Tank -micro coil
3. Transformed Kanger MT3 to MT3S - micro coil

For King e-pipe i like the most SMOKTECH 6.0ML PYREX GLASS DUAL COIL TANK with BOGE LR prepunched 1 hole (2mm)

[Pezz]

Fogger with cotton for sweets

RSST with reduced chamber - Rope and mesh wick - For tobaccos

Immortalizer (Clone) with cotton for dripping

Silverdog V2 for out and about

[steve386]

At the moment my list is:-

1) Kayfun 3.1 clone from Fasttech
2) Kayfun lite original from Cloud9
3) Ody + all variations (Ithaka, Terminator, kayfun insert etc.)

I blame Blakey for ALL of the above

[blakey]

Nov 30, 2013 21:38:54 GMT steve386 said:

At the moment my list is:-

1) Kayfun 3.1 clone from Fasttech
2) Kayfun lite original from Cloud9
3) Ody + all variations (Ithaka, Terminator, kayfun insert etc.)

I blame Blakey for ALL of the above

Duly noted
I can live with it though, you should see the list that jason blames me for

.