Pre made nr/r/nr wire

[Greg]

Can anyone advise where I can but premade wire where the nr is 0.2mm wire. The couple of sites I've found don't specify and the stuff I've bought from one vendor is too thick at 0.25mm I think.

[Deleted]

I don't know the diameter of the wires that I buy from Billy at Grey Haze but I have used them with no problems on the Diver, Ithaka and iAtty.

[Super-Shiny]

Greg have a read here or even ask whatever question you need, they will answer anything regarding the Sophia, also the maker of the Sophia is always on there answering questions: Clicky

It's where i got all my info and knowledge.

[Greg]

Thanks shiny, I compared the grey haze wires I bought to those in my replacement ceramics and the grey haze is definitely thicker nr. I compared the pre built coils to my 0.2 kanthal and it's the same. I'm therefore sure my Sophia issues are due to the thicker wire in the positive pin.

[Super-Shiny]

Greg there is a post on that link i gave about the thickness of the wire, but what page it is a ain't got a clue.

[Deleted]

Dec 31, 2013 18:40:25 GMT Greg said:

Thanks shiny, I compared the grey haze wires I bought to those in my replacement ceramics and the grey haze is definitely thicker nr. I compared the pre built coils to my 0.2 kanthal and it's the same. I'm therefore sure my Sophia issues are due to the thicker wire in the positive pin.

You could run the edge of a knife blade across the end of the wire that folds into 510 end of the ceramic cup to slim it down to 0.2mm? 

[jimthecarper]

A lot of NR/Res pre mades are .25 on the No res sections. Easier to weld and less resistance. (Even No res has a little resistance)
I think Grey Haze use .2 or .22 on the no res.

[Greg]

Dec 31, 2013 18:47:28 GMT @freefromsmoking said:

Dec 31, 2013 18:40:25 GMT Greg said:

Thanks shiny, I compared the grey haze wires I bought to those in my replacement ceramics and the grey haze is definitely thicker nr. I compared the pre built coils to my 0.2 kanthal and it's the same. I'm therefore sure my Sophia issues are due to the thicker wire in the positive pin.

You could run the edge of a knife blade across the end of the wire that folds into 510 end of the ceramic cup to slim it down to 0.2mm? 

Yep I was thing about doing something like that but longer term wanted 0.2 premade.

[Greg]

Dec 31, 2013 18:49:10 GMT jimthecarper said:

A lot of NR/Res pre mades are .25 on the No res sections. Easier to weld and less resistance. (Even No res has a little resistance)
I think Grey Haze use .2 or .22 on the no res.

I pretty sure the grey haze wires I have are .25

[Super-Shiny]

I think GH get the same as these: www.vapor-freak.de/zubehoer/Selberwickeln/Fertigdraht

So they would be:

Welded wire finished. Made of NiCr wire. Resistance middle part diameter is 0.15mm, no Resistance outer wires diameter 0.25mm.

[Super-Shiny]

Greg don't know if these will work: www.vaperus.ie/rebuilding-supplies/379-rainbow-killer-coils.html

wire with no-resistance lead

resistance wire diameter=0.15mm

lead wire diameter=0.15mm..(length 40mm)

[Deleted]

Greg I don't know about the Sophia, but in the past I have recoiled my Diver using only 0.2 mm Kanthal resistance wire and I found no noticeable difference in performance ... the relatively short legs on the coil cause negligible voltage drop.

[Greg]

Strange no one sells 0.2, maybe I'll just get one of Mevs zappers and some 0.2 from vape mesh company then I can give microcoils a go in Sophia and maybe even cotton wool

[Greg]

Finally got it working

i463.photobucket.com/albums/qq353/gregbarrows/793c3542f4e3c6856de3c8b8b7301a97.jpg

[boyofford]

Fasttech do NR part at .22, spotted there wires/coils the other day www.fasttech.com/products/1411/10004596/1521300-pre-made-welded-wires-nr-r-nr-100-pack..... might be bit of a weight at the moment, especially as it still may be to big?