Russian 91% question Fasttech

[lenny59]

Anyone got one of the 3 different ones on Fasttech ?

If you have is it any good and which one did you get ?

cheers

[marlbororman]

ive got the kayfun 3.1 clone stainless steel. Been my everyday vape on a vamo v5 since middle of january if that helps. All ive done was bath it a few times to get rid the machine oil, and changed the post screws where the coil fastens to. Its perfect. two tanks of red astaire daily I know, im an addict lol And it is full stainless too Got two kayfun lite clones inbound too.

[Deleted]

lenny59 I got this one

www.fasttech.com/products/0/10006473/1552300-russian-91-styled-rebuildable-atomizer-4-5ml

I had trouble with the post screws but seem to be sending SS screws now so its been reported but if they don't, you can buy cheap ss screws on ebay. I think a pack of five is only 99p.
I told them about the issue and they have sent out a replacement base ??? so that means I will have two bases
Some people had problems with juice channels being to narrow or non existent but people have been using a 1.8 grinding bit to make them deeper to allow more vapour.
Some people have reported the threads being awful but many have found them okay.

Have a look at the reviews and discussion pages on fasttech

The russian I have link has a star rating 4.4 out of five. This would say most people are please with it.
I am fairly happy with my one but the channels could do with being a bit deeper. waiting on a 1.8 grinding bit of the neighbour. Overall its quality and whatever problems arises can easily be sorted if the buyer is unlucky.

[marlbororman]

yer i was looking at that as next possible buy but still thinking bout this


www.desire-ecig.com/The-Russian-91-Atomizer


out of stock at min though again.

[grahamjames]

I bought the Tobeco Russian from Vapor Break and it has a few problems - the fill screw dethreads after a few uses so I got a bag of spares.
The chimney doesn't seal to the top cap so it floods, currently have a silicon sleeve over the chimney top to prevent that.
It whistles.
Went to Desire Ecig to get their Russian but out of stock so I bought 2 of their kayfun lites instead. I am pleased with them.
There is no airflow control but for me the draw is just right and no whistling !
The screws are soft but easily and cheaply replaced. The threads on the main parts are a little crunchy but acceptable. The chimney seals really well.
I plan to buy 2 more of these.
I bought a nemesis from them at the same time to get over the 60 dollar threshold for free postage and that too is ok.
Best bit of the whole transaction - 11 days from ordering to unpacking

[tokari]

Feb 28, 2014 20:55:50 GMT stamina said:

lenny59 I got this one

www.fasttech.com/products/0/10006473/1552300-russian-91-styled-rebuildable-atomizer-4-5ml

I had trouble with the post screws but seem to be sending SS screws now so its been reported but if they don't, you can buy cheap ss screws on ebay. I think a pack of five is only 99p.
I told them about the issue and they have sent out a replacement base ??? so that means I will have two bases
Some people had problems with juice channels being to narrow or non existent but people have been using a 1.8 grinding bit to make them deeper to allow more vapour.
Some people have reported the threads being awful but many have found them okay.

Have a look at the reviews and discussion pages on fasttech

The russian I have link has a star rating 4.4 out of five. This would say most people are please with it.
I am fairly happy with my one but the channels could do with being a bit deeper. waiting on a 1.8 grinding bit of the neighbour. Overall its quality and whatever problems arises can easily be sorted if the buyer is unlucky.

I got this one as well, delivered end of Jan.  It came with SS screws and the juice channels seemed deep enough and not had any problems with wicking.  Again, my threads were pretty smooth, all but the chimney top which was a bit scratchy to start off with but ok now.

[lenny59]

Thanks to everyone for the replies

A couple of you have mention the fasttech one being Ok.......Thanks for the link.....I am liking the idea of the airflow option

Worth a try for the money.....don't mind having to make a few adjustments ....that's a given with the fasttech items I have bought in the past

Again thanks for the input from all of the above posts

[richvapers]

i have this one comeing from fasttech.

Should be with me any day now. (tomorrow would be great)
And will let you know what i think of it when it arrives.

Also worth picking up one of these.



Works great on the kayfun i have, and with a chimney build? does eliminate any leaking isues from the air hole.
For £3.36? it is a must buy.

Cheers....Rick

[lenny59]

Mar 1, 2014 0:02:40 GMT richvapers said:

i have this one comeing from fasttech.

Should be with me any day now. (tomorrow would be great)
And will let you know what i think of it when it arrives.

Also worth picking up one of these.



Works great on the kayfun i have, and with a chimney build? does eliminate any leaking isues from the air hole.
For £3.36? it is a must buy.

Cheers....Rick

yeah rich ....do let us know how you get on with this..... richvapers