Finally Arrived

[chill36]

Well at long last my Nemisis and Kraken have arrived from fast tech,  have to say pretty impressed with it. Did my first rebuild got coils to 0.7 with 0.28 gauge wire and 7 wraps on dual core with cotton vaps very nice.


I had 2 little complaints on the Kraken :


1. The 'O' rings do not seem tight enough as glass tank is quite loose.
2. One of the negative screws the stamping is to faint to get screwdriver in, also the wick holes are missing the screws

Dont suppose anyone has any spares o rings or spare the screws.


Regards
Chill36

[Q]

Mine arrived today as well, looks impressive but I must admit I haven't a clue what to do with it
This is the one I got

[charon]

Jul 9, 2014 19:22:01 GMT Q said:

Mine arrived today as well, looks impressive but I must admit I haven't a clue what to do with it
This is the one I got

Coil it wick it fill it stick on your mod and suck it!!!! easy problem solved

[Deleted]

Jul 9, 2014 19:14:47 GMT chill36 said:

Well at long last my Nemisis and Kraken have arrived from fast tech,  have to say pretty impressed with it. Did my first rebuild got coils to 0.7 with 0.28 gauge wire and 7 wraps on dual core with cotton vaps very nice.


I had 2 little complaints on the Kraken :


1. The 'O' rings do not seem tight enough as glass tank is quite loose.
2. One of the negative screws the stamping is to faint to get screwdriver in, also the wick holes are missing the screws

Dont suppose anyone has any spares o rings or spare the screws.


Regards
Chill36
You should have one grub screw to block a wick hole if your only doing a single coil.
The tank should def not be loose, prob best to find a site that sells the genuine article and get some orings from there.
As for the screws you can get them on flebay for pennies.

[erik514]

An easy fix for the o rings is dental floss. Take the o rings off and put 2 or 3 wraps of floss where they go and then put the o ring back on. Guaranteed tight fit and no leaks
As for the screws personally I don't have any of them in my kraken and I run it single coil. I think it helps it to wick better if the screws are gone

[erik514]

Jul 9, 2014 19:22:01 GMT Q said:

Mine arrived today as well, looks impressive but I must admit I haven't a clue what to do with it

Have a look on youtube for a guy called Robert Ellis.  He does a couple of videos about genesis atomisers that helped me to get mine running.  Don't forget you can wick a genesis with silica or cotton as well as stainless steel

[chill36]

Jul 9, 2014 19:51:18 GMT erik514 said:

An easy fix for the o rings is dental floss. Take the o rings off and put 2 or 3 wraps of floss where they go and then put the o ring back on. Guaranteed tight fit and no leaks
As for the screws personally I don't have any of them in my kraken and I run it single coil. I think it helps it to wick better if the screws are gone

Many thanks for the advice will try the dental floss


Did I mention my kraken vaps like a bitch lol

[boyofford]

Jul 9, 2014 19:51:18 GMT erik514 said:

An easy fix for the o rings is dental floss. Take the o rings off and put 2 or 3 wraps of floss where they go and then put the o ring back on. Guaranteed tight fit and no leaks
As for the screws personally I don't have any of them in my kraken and I run it single coil. I think it helps it to wick better if the screws are gone

Good idea, off to try that with few of my drippers.

[decoy]

Jul 9, 2014 19:51:18 GMT erik514 said:

An easy fix for the o rings is dental floss. Take the o rings off and put 2 or 3 wraps of floss where they go and then put the o ring back on. Guaranteed tight fit and no leaks
As for the screws personally I don't have any of them in my kraken and I run it single coil. I think it helps it to wick better if the screws are gone

yer not just a pretty face
top idea

op if your using silica to wick your coil run it in to both holes 
if your using mesh good luck lol no but heat it like a bitch then put juice on it and set the sucker on fire and let it burn out do the juice thing 3 or 4 times it builds up a carbon layer on it so you dont get shorts then you tube on how to roll it main tip it fold over one of the ends before rolling so it ends up on the outside folded in.you can add cotton wool to it as well


my personal fave was 2 mesh wicks then warping cotton wool round them to go throw the coil(kinda like an auto dripper)
hope that helps

[chill36]

I have been using cotton works really nice.

Tried the dental floss much better.

Had the square arrive that unfortunately has a leak one the plastic windows to the metal case bit so people be ware of this from fasttech.

But all in all 2 out of 3 clone tanks work beautifully and the 2 nemisis bother work fine even though they are different lengths.

Regards

Chill36