Goodsense 306 DCA Wanted .. Kinda

[bluemagnum]

Still a good vape the 901 perps, I have a few left too. Trouble is with the good ones, they last too long!

[Perpetua]

11 watts on the Darwin and they're still a really nice vape for me Blue.

Softer than the 306 or 510 which is an enjoyable change . . . . .

[bluemagnum]

I've just rooted one out of my box, 3.1ohm, turned it down to 10 watts and the flavour is lovely. 10 drops in it too.

[Deleted]

Im swaying towards one of these now... has anyone had one ... And Prep is correct the shield was for the 901 i should have known, ive got loads of the Liberty flights version, bought for my screwdriver way back when ....lol

[bluemagnum]

There was a thread over the road about those last year. I don't think they worked very well. If you have a shield, you can make your own with a carto tube or a 510 tube. Easy to do.

[Deleted]

Ive got a drip shield but struggling to see how you could make one with a carto.

[bluemagnum]

Jul 28, 2014 22:02:08 GMT @agenthoover said:

Ive got a drip shield but struggling to see how you could make one with a carto.

A 306 is basically a 510 without a tube. You cut a quarter of an inch off the bottom of the plastic tip that comes with the 306 and slide it on where the tip fits. Get your carto tube and tap it onto the plastic till it gets to the bottom.( You also need a 510-510 adapter). Place the 306 in the adapter, slide the shield onto it with the hole at the top and fit drip tip. The o rings in the shield stop any juice leaking out and suck it back into the 306 through the gap in the adapter.

[Deleted]

Jul 28, 2014 15:27:30 GMT Pepperty said:

I've got the provari one made by siam mods, with the matching drip tip, does look rather bling for a simple 306
but I quite like it.

I do use other drippers but theres a lot to be said for a 306, you just wash off old juice and throw on new. Its what I choose to taste juices with. For dripping I've an ebarron and a grail but for bog standard --what does it taste of? its a 306 every time!

Will that hang over the edges of a vaporshark... they are 20mm thick aproxx

[Deleted]

Jul 28, 2014 10:30:50 GMT manicmedic said:

I had a gsv DCA and swapped it recently due to gurgling with any more than 4 drops. I then bought this Siam one which I feel is far better and fits all 306 atties I've thrown at it.

For that to fit just about any 306 it must have a taper inside has it   ?

[Pepperty]

@agenthoover The siam mods drip shield I have is really small. I've just taken a snap so you can see and know its size. For comparison its on an SD 300mAh screwdriver next to a provari mini small eh!

[Deleted]

Bloody hell, its tiny, will go for one of those ... just do it, get the job done ..lol.. they dont seem to have them on pinkmule but this was linked to earlier in the thread.. same thing ? gr-modders.com/75-drip-shield-for-306-atomizers.html plus is this your driptip gr-modders.com/49-zantos-a-special-drip-for-provari.html and thanks for taking the time to take the pic

[Pepperty]

Yes that my pair, and the 306 just fits in below, its not a big long tube or anything! and it's not going to overhang anything haha
but its a nice way to bling up a basic 306 atty

[Deleted]

So come on then... what are the pitfalls.. im sick of buying crap lately ..lol... or is it spot on, keep in mind you get blamed if its no good ...lol

[Pepperty]

tbh it doesnt really serve a purpose does it? It doesnt really come with a well for juice to sit in? its just....a bit posher than the normal plastic 306 mouthpiece. Its going to cost you 20 odd euro for some stainless steel with twirly bits on it... ???

Dont expect me to big it up now my diver v1 base and grail, now that is useful, has a well for juice and lots of ways of rebuilding to suit....

[Deleted]

Yeah but that keeps me stuck on the rebuildables booooo hoooo... im going back to the easy life and now that 306's aint as popular now you can get them cheap as chips...