Rose v2 clone

[Ripshod]

Sept 21, 2014 14:01:36 GMT flavourtank said:

Been having a few moments with this and I dont know why. I changed coil filled her up and then it pisssed out the airflow controller It happened 3 times.

Do you think it could be lack of rayon???

If you're getting juice out of the air hole then it's flooding. Either it needs just a little more wick in the juice channels, ooooooooor you've damaged an o-ring. Check the rings in the cap and the base. If it's too little wick then it won't leak any when it's stood upright (a little clue). Also make sure both chimey sections are screwed together correctly.

Once happened to me - I didn't screw the airflow right down before fitting the bottom tank section. It leaked through a gap above the airflow ring and I thought it was from the air holes.

[flavourtank]

Sept 21, 2014 14:26:53 GMT Ripshod said:

Sept 21, 2014 14:01:36 GMT flavourtank said:

Been having a few moments with this and I dont know why. I changed coil filled her up and then it pisssed out the airflow controller It happened 3 times.

Do you think it could be lack of rayon???

If you're getting juice out of the air hole then it's flooding. Either it needs just a little more wick in the juice channels, ooooooooor you've damaged an o-ring. Check the rings in the cap and the base. If it's too little wick then it won't leak any when it's stood upright (a little clue). Also make sure both chimey sections are screwed together correctly.

Once happened to me - I didn't screw the airflow right down before fitting the bottom tank section. It leaked through a gap above the airflow ring and I thought it was from the air holes.

ill check them in a mo, I fill from top and when it gets to a point it pisses out the airflow hole, might put some rayon in juice channels

[Ripshod]

Sept 21, 2014 14:41:12 GMT flavourtank said:

ill check them in a mo, I fill from top and when it gets to a point it pisses out the airflow hole, might put some rayon in juice channels

That's part of your problem right there. These tanks rely on a vacuum to hold the juice in. When you replace the top tank section you're actually pressurising the tank. You will lose some juice. Best to just open the juice control a tiny amount and vape your head off til you've used the excess juice.

My previous post was wrong. I was rebuilding my fogger at the time and that was what was in my head lol.

When you do get into it make sure also that the wicks haven't moved leaving the channels wide open.

[flavourtank]

Sept 21, 2014 14:43:29 GMT Ripshod said:

Sept 21, 2014 14:41:12 GMT flavourtank said:

ill check them in a mo, I fill from top and when it gets to a point it pisses out the airflow hole, might put some rayon in juice channels

That's part of your problem right there. These tanks rely on a vacuum to hold the juice in. When you replace the top tank section you're actually pressurising the tank. You will lose some juice. Best to just open the juice control a tiny amount and vape your head off til you've used the excess juice.

My previous post was wrong. I was rebuilding my fogger at the time and that was what was in my head lol

ok so if I fill from top I should leave juice control open a bit??

[Deleted]

Sept 21, 2014 14:24:17 GMT Dan said:

Sept 21, 2014 12:09:17 GMT @tazmania441 said:

What's your set up on it Dan ? I find a larger centre on the coil with cotton makes the draw better as its creating more vape....

I'm using a 2mm diagonal coil per the eden mods youtube video but using 0.3 wire. Reads at 1ohm on the dani.

You think I should try a 3mm coil?

I used 2mm duals in the genuine for the most part but I didn't really have it that long to experiment much!

2mm should be fine mate

[Ripshod]

Sept 21, 2014 14:48:51 GMT flavourtank said:

ok so if I fill from top I should leave juice control open a bit??

You should close the juice control completely before removing the top. When you've filled and replaced the top (mopping up the juice that oozes out) open the juice control a maximum of half a turn. Then vape like mad til you lose flavour. Everything should be fine then to go back to your old settings.

[flavourtank]

Sept 21, 2014 15:00:46 GMT Ripshod said:

Sept 21, 2014 14:48:51 GMT flavourtank said:

ok so if I fill from top I should leave juice control open a bit??

You should close the juice control completely before removing the top. When you've filled and replaced the top (mopping up the juice that oozes out) open the juice control a maximum of half a turn. Then vape like mad til you lose flavour. Everything should be fine then to go back to your old settings.

ok ive checked oring and its fine ive made sure juice channels are filled.... ill now try this way of filling

[Dan]

Sept 21, 2014 14:54:42 GMT @tazmania441 said:

Sept 21, 2014 14:24:17 GMT Dan said:

I'm using a 2mm diagonal coil per the eden mods youtube video but using 0.3 wire. Reads at 1ohm on the dani.

You think I should try a 3mm coil?

I used 2mm duals in the genuine for the most part but I didn't really have it that long to experiment much!

2mm should be fine mate

Maybe I just need to get used to it..

Going to have another play tonight and vary the amount of cotton I use. This kgd wicks so quickly (even compared to rayon) but is a bit€? to get the right amount in the coil.. that's the only thing I've changed since I had the genuine.. used normal cotton pleat in that..

Then I think I need to find a suitable mod to put it on.. Dani just can't keep up at 20w without changing the batteries every few hours..

What do you use for yours? The Kato?

[Ripshod]

I'm still on the same first coil ever (since GB1) and not 100% sure. 2.5mm dia 0.4mm kanthal, 8 turns giving 1.2ohms, I think lol. Wicked with KGD, hitting 15watts seems to be the sweet spot. Gonna try 0.28 twisted later - will let you know. On a DNA30 clone.

Don't ask about the other one. Hits 20watts tho.

[flavourtank]

Sept 21, 2014 15:11:16 GMT flavourtank said:

Sept 21, 2014 15:00:46 GMT Ripshod said:

You should close the juice control completely before removing the top. When you've filled and replaced the top (mopping up the juice that oozes out) open the juice control a maximum of half a turn. Then vape like mad til you lose flavour. Everything should be fine then to go back to your old settings.

ok ive checked oring and its fine ive made sure juice channels are filled.... ill now try this way of filling

think thats done it as I didn't have ra piss everywhere thanks Ripshod

[lairey]

Sept 21, 2014 15:14:45 GMT Dan said:

Sept 21, 2014 14:54:42 GMT @tazmania441 said:

2mm should be fine mate

Maybe I just need to get used to it..

Going to have another play tonight and vary the amount of cotton I use. This kgd wicks so quickly (even compared to rayon) but is a bit€? to get the right amount in the coil.. that's the only thing I've changed since I had the genuine.. used normal cotton pleat in that..

Then I think I need to find a suitable mod to put it on.. Dani just can't keep up at 20w without changing the batteries every few hours..

What do you use for yours? The Kato?

BEC Pro Dan

[Dan]

Sept 21, 2014 15:22:21 GMT lairey said:

Sept 21, 2014 15:14:45 GMT Dan said:

Maybe I just need to get used to it..

Going to have another play tonight and vary the amount of cotton I use. This kgd wicks so quickly (even compared to rayon) but is a bit€? to get the right amount in the coil.. that's the only thing I've changed since I had the genuine.. used normal cotton pleat in that..

Then I think I need to find a suitable mod to put it on.. Dani just can't keep up at 20w without changing the batteries every few hours..

What do you use for yours? The Kato?

BEC Pro Dan

That's way to complicated. Specs are good but who really needs 12v output??

I'm thinking ipv3 or sigelei 100w at the minute for regulated, and kato for mechanical..

[Greg]

Sept 21, 2014 15:20:26 GMT flavourtank said:

Sept 21, 2014 15:11:16 GMT flavourtank said:

ok ive checked oring and its fine ive made sure juice channels are filled.... ill now try this way of filling

think thats done it as I didn't have ra piss everywhere thanks Ripshod

If you fill from top after putting top cap back on and cleaning the ooze turn it upside down and then open the JC half a turn and leave upside down for a couple of seconds, this relieved the pressure pushing air out rather then juice and means you don't have to Vape like mad 

[lairey]

Sept 21, 2014 15:32:02 GMT Dan said:

Sept 21, 2014 15:22:21 GMT lairey said:

BEC Pro Dan

That's way to complicated. Specs are good but who really needs 12v output??

I'm thinking ipv3 or sigelei 100w at the minute for regulated, and kato for mechanical..

It's not at all complicated to use and it does look beautiful

[flavourtank]

Sept 21, 2014 15:55:07 GMT Greg said:

Sept 21, 2014 15:20:26 GMT flavourtank said:

think thats done it as I didn't have ra piss everywhere thanks Ripshod

If you fill from top after putting top cap back on and cleaning the ooze turn it upside down and then open the JC half a turn and leave upside down for a couple of seconds, this relieved the pressure pushing air out rather then juice and means you don't have to Vape like mad 

ta for that, when I first coiled it and refilled I never had this problem only since today when I recoiled.