Rose v2 clone

[flavourtank]

Sept 27, 2014 20:05:20 GMT Ripshod said:

May be a bit late, but twisted 0.3mm for 1.0 ohms. Running at 20 watts on a focal Hana clone.

not late at all, was asking before I purchase some. Is 0.3 ok for 1.5-2ohm??

I do want to try lower ohm at some point

[Ripshod]

Sept 27, 2014 20:08:08 GMT flavourtank said:

Sept 27, 2014 20:05:20 GMT Ripshod said:

May be a bit late, but twisted 0.3mm for 1.0 ohms. Running at 20 watts on a focal Hana clone.

not late at all, was asking before I purchase some. Is 0.3 ok for 1.5-2ohm??

2mm microcoil  of 7 turns should hit somewhere around the mark for ya! 0.3 is good, but the difference to 0.28mm is so marginal it doesn't really matter to me.

Honestly you'll build your kit up to maybe 4 or 5 different sizes. Once you get into building your own, you'll see the benefit of different coils for different juices

[arron]

Sept 27, 2014 20:05:20 GMT Ripshod said:

May be a bit late, but twisted 0.3mm for 1.0 ohms. Running at 20 watts on a focal Hana clone.

^^agrred^^ twisted .3mm over a 2.4mm or 3mm screwdriver for me between 1-1.4 ohm, flavour is fantastic

[flavourtank]

arron and Ripshod thanks for that, I haven't got a clue what wire im using now (it works tho)

Will have search for some 0.3

Thanks

[xs2man]

I'm another using twisted 0.3mm. I find the twisted to be much easier to locate the holes under the ceramic, although I do think I was possibly building it a little ares about tit.

Anyway, I'm only around 0.6 Ohm according to my DNA (my atty reader did read it at 0.85 ohm, stupid FT, now reading 0.66). Might try a twisted 0.25 next time, prefer my tanks closer to 1.3 ohm's usually.

[Dan]

Hi guys, i anyone having issues with the 510 connection with their roses?

I'm finding the ohms readings to be all over the place depending how far out I have the adjustable screw. 1.6ohm coil has read as high as 3.6 so far with the screw undone 1/2 a turn

I'm starting to think it's the o ring being too thin to stabilise the pin but I can't for the life of me find the size I need to order

Any ideas chaps and chappettes?

[Deleted]

Oct 6, 2014 11:10:07 GMT Dan said:

Hi guys, i anyone having issues with the 510 connection with their roses?

I'm finding the ohms readings to be all over the place depending how far out I have the adjustable screw. 1.6ohm coil has read as high as 3.6 so far with the screw undone 1/2 a turn

I'm starting to think it's the o ring being too thin to stabilise the pin but I can't for the life of me find the size I need to order

Any ideas chaps and chappettes?

Nip up the grub screws holding your build rookie

[arron]

^^^+1^^^

It's the grub screw that's come loose mate

[Dan]

Oct 6, 2014 11:15:16 GMT @tazmania441 said:

Oct 6, 2014 11:10:07 GMT Dan said:

Hi guys, i anyone having issues with the 510 connection with their roses?

I'm finding the ohms readings to be all over the place depending how far out I have the adjustable screw. 1.6ohm coil has read as high as 3.6 so far with the screw undone 1/2 a turn

I'm starting to think it's the o ring being too thin to stabilise the pin but I can't for the life of me find the size I need to order

Any ideas chaps and chappettes?

Nip up the grub screws holding your build rookie

Cheeky git

The grub screws are fine, The build is fine.

If i put it on the Dani (which means adjusting (lengthening) the 510 screw of the rose) it jumps around all over the place. Same story for the Vtr, Svd, and my ohms reader.

If I then screw the rose's pin back in, put it on the Sigelei 100w, raise the mods pin up to the rose, it reads bang on what it's supposed to.

well, smartarses? Tease-smiley

[Greg]

Dan check the threads on both halves of the 510, ie brass pin and Ali disc. Threads were goosed on one of mine with same results as you.

[Deleted]

Oct 6, 2014 11:44:33 GMT Dan said:

Oct 6, 2014 11:15:16 GMT @tazmania441 said:

Nip up the grub screws holding your build rookie

Cheeky git

The grub screws are fine, The build is fine.

If i put it on the Dani (which means adjusting (lengthening) the 510 screw of the rose) it jumps around all over the place. Same story for the Vtr, Svd, and my ohms reader.

If I then screw the rose's pin back in, put it on the Sigelei 100w, raise the mods pin up to the rose, it reads bang on what it's supposed to.

well, smartarses? Tease-smiley

It means only your Sig is working properly

[Dan]

Oct 6, 2014 11:48:08 GMT Greg said:

Dan check the threads on both halves of the 510, ie brass pin and Ali disc. Threads were goosed on one of mine with same results as you.

Already checked those fella, look fine.

Besides which, i they were goosed, where the heck would we get spares

Kinda tempted to get a v1>v2 kit from Eden themselves but think they might get suspicious with me ordering 5

[Dan]

Oct 6, 2014 11:52:34 GMT @tazmania441 said:

Oct 6, 2014 11:44:33 GMT Dan said:

Cheeky git

The grub screws are fine, The build is fine.

If i put it on the Dani (which means adjusting (lengthening) the 510 screw of the rose) it jumps around all over the place. Same story for the Vtr, Svd, and my ohms reader.

If I then screw the rose's pin back in, put it on the Sigelei 100w, raise the mods pin up to the rose, it reads bang on what it's supposed to.

well, smartarses? Tease-smiley

It means only your Sig is working properly

We are in a good mood aren't we

Have you still got your authentic jobby?

If so, could you measure the oring on the 510 pwwweeeaaase?

Been looking for over an hour for the size and got no-where..

[Deleted]

Sold mine after the first GB seeing as the stumpy fit the clone and couldn't fault the performance I cashed in while it still carried full value sorry buddy

[Dan]

No worries. Trawling UKV at the minute