Struggling with IPV V2

[VapingBad]

Oct 8, 2014 20:27:30 GMT Dave said:

Oct 8, 2014 20:18:35 GMT VapingBad said:

So the power cuts out after 4 secs on the higher setting, this could be a weak battery or connection problem.  Give the battery and the terminals a good clean with IPA, meths or vodka and the same for the atty connection.  And check the adjuster screw in the 510 connection in making contact by unscrewing a bit at a time until the atty won't sit flush.

Sounds like a plan, I'll give that a shot tomorrow as I've had 4 bottles of Brahma and those little screws to take the back off need some proper care 

I lost one at the last vape meet.

[ruffdog]

Oct 8, 2014 20:18:35 GMT VapingBad said:

Oct 8, 2014 19:23:04 GMT Dave said:

If I set the wattage at 7 it will vape but if I shift it up to 9 it will vape for 4 seconds then hit a brick wall and stop?

So the power cuts out after 4 secs on the higher setting, this could be a weak battery or connection problem.  Give the battery and the terminals a good clean with IPA, meths or vodka and the same for the atty connection.  And check the adjuster screw in the 510 connection in making contact by unscrewing a bit at a time until the atty won't sit flush.

Hang about  ?? ?   on the 510 screw.   It's a spring loaded 510 pin.   Well mine is.
I saw something about unscrewing it because (it is an actual screw) but may damage the connection.
I don't know . . .  . Just thought i should mention.   You shouldn't need to adjust the 510 as it is a spring pin anyway.
I COULD BE WORNG but mine is.

Ruffie.

[VapingBad]

Oct 8, 2014 20:31:55 GMT ruffdog said:

Oct 8, 2014 20:18:35 GMT VapingBad said:

So the power cuts out after 4 secs on the higher setting, this could be a weak battery or connection problem.  Give the battery and the terminals a good clean with IPA, meths or vodka and the same for the atty connection.  And check the adjuster screw in the 510 connection in making contact by unscrewing a bit at a time until the atty won't sit flush.

Hang about  ?? ?   on the 510 screw.   It's a spring loaded 510 pin.   Well mine is.
I saw something about unscrewing it because (it is an actual screw) but may damage the connection.
I don't know . . .  . Just thought i should mention.   You shouldn't need to adjust the 510 as it is a spring pin anyway.
I COULD BE WORNG but mine is.

Ruffie.

My one (from Liberty Flights) has a cross head screw to adjust the 510.

[macmagoo]

The 510 connection screw on the IPV2 can be unscrewed right out so it should be fully adjustable.

[ruffdog]

Oct 8, 2014 20:37:47 GMT VapingBad said:

Oct 8, 2014 20:31:55 GMT ruffdog said:

Hang about  ?? ?   on the 510 screw.   It's a spring loaded 510 pin.   Well mine is.
I saw something about unscrewing it because (it is an actual screw) but may damage the connection.
I don't know . . .  . Just thought i should mention.   You shouldn't need to adjust the 510 as it is a spring pin anyway.
I COULD BE WORNG but mine is.

Ruffie.

My one (from Liberty Flights) has a cross head screw to adjust the 510.

Mine looks the same but the whole head and the delrin surrounding it moves up and down and is spring loaded (a little scratchy but it is sprung)
try pressing yours in and see if it is the same please

Toby

[VapingBad]

I have not needed to adjust mine so far Toby ruffdog as there is some compliance with the screw full in. I've not had any problems at alll with mine, but it only gets used if I want to go over 30 W as I much prefer my DNAs and it has a nasty voltage spike for the first half second at lower watts.