Aspire Nautilus Mini

[danliddle]

Recently bought a new Aspire Nautilus Mini and had it with in two days and the Coil burnt out and I went and bought another couple and the same keeps happening over the past week but when I had a Nautilus before a never had any bother with it the Coil use to last about 3 weeks anyone know why this can happen a normally smoke at about 9.0 Watts or 4.2 Volts ?

Cheers

[Perpetua]

Some suggestions here danliddle:

www.e-cigarette-forum.com/forum/new-members-forum/601888-nautilus-aspire-burnt-coil-taste-again-again.html

https://www.reddit.com/r/electronic_cigarette/comments/21w3u9/aspire_nautilus_burnt_taste/

The eliquid and wattage you're using could also be factors.

[danliddle]

Cheers being reading through i think its cos ive been changing the Coil & not leaving it to settle propley and just toking on it straight away I only smoke on about 9.0 watts and the coil is a 1.8 aswell

[Tom]

Dec 20, 2014 17:10:47 GMT danliddle said:

Cheers being reading through i think its cos ive been changing the Coil & not leaving it to settle propley and just toking on it straight away I only smoke on about 9.0 watts and the coil is a 1.8 aswell

I would say you are probably burning the wicking material before it gets chance to fully saturate.

Before putting the tank on the coil, put 5-6 drops of liquid directly on the material through the top and fully wet it.

Should be go to go from off after putting it on your tank then

[Q]

Dec 19, 2014 21:12:48 GMT danliddle said:

Recently bought a new Aspire Nautilus Mini and had it with in two days and the Coil burnt out and I went and bought another couple and the same keeps happening over the past week but when I had a Nautilus before a never had any bother with it the Coil use to last about 3 weeks anyone know why this can happen a normally smoke at about 9.0 Watts or 4.2 Volts ?

Cheers

Biggest problem I can see is that you should be VAPING it, you're NOT a smoker

[djs]

4.2v is more or less my favourite setting. It (on the iStick)"claims" to be 9-10 watts, but of course, it's not... it's much more.
Having said that, it should not be burning out.... I've not had that (yet) with either 1.6 or 1.8ohm coils.

What ratio is your liquid?(PG/VG) because it won't wick over 50% VG fast enough if you are vaping it hard.
What airflow setting are you using?

[goneforagasper]

What I tend to do when changing these coils is to do it last thing at night so next morning they are well primed

[djs]

Dec 20, 2014 17:33:37 GMT goneforagasper said:

What I tend to do when changing these coils is to do it last thing at night so next morning they are well primed

I vape them 30 seconds after fitting them. It's all in the priming. They can take a real soaking....

[danliddle]

Dec 20, 2014 17:33:26 GMT djs said:

4.2v is more or less my favourite setting. It (on the iStick)"claims" to be 9-10 watts, but of course, it's not... it's much more.
Having said that, it should not be burning out.... I've not had that (yet) with either 1.6 or 1.8ohm coils.

What ratio is your liquid?(PG/VG) because it won't wick over 50% VG fast enough if you are vaping it hard.
What airflow setting are you using?

All the liquids am using are normally 50 50 and not sure on which airflow setting its about third hole in didn't know you could tell the settings

[danliddle]

Dec 20, 2014 17:23:09 GMT Tom said:

Dec 20, 2014 17:10:47 GMT danliddle said:

Cheers being reading through i think its cos ive been changing the Coil & not leaving it to settle propley and just toking on it straight away I only smoke on about 9.0 watts and the coil is a 1.8 aswell

I would say you are probably burning the wicking material before it gets chance to fully saturate.

Before putting the tank on the coil, put 5-6 drops of liquid directly on the material through the top and fully wet it.

Should be go to go from off after putting it on your tank then

A will try doing it that way next time cheers

[djs]

Dec 20, 2014 17:49:40 GMT danliddle said:

All the liquids am using are normally 50 50 and not sure on which airflow setting its about third hole in didn't know you could tell the settings

That could be the problem. The only dry hit I ever had (not that it was bad, exactly) was using 50/50 liquid.... at 4.2v.
I was so surprised, I did 3 or 4 massive pulls (no power) with my finger over the airhole (almost completely) and sucked in a decent amount of liquid.
It would have dry hit again.... for sure... you get a feel for these things.