tank spacer tips please

[ragjoy]

does anyone have any tips for a washer type idea that i can place between the bottom of the tank and my device.
i need to help the air flow just a fraction, it would need to be half the thickness of a credit card.
i im using the istick 50 with innokin t18 tanks, the tank tightens down and the tank air flow vent doesnt line up with the istick air vent.
i dont need to line them up just create a slight gap.
ive tried it with folded and cut paper but its fiddly putting the tank back on each time.
any tips please.

[Roscopecotrain]

Mar 7, 2016 13:41:44 GMT ragjoy said:

does anyone have any tips for a washer type idea that i can place between the bottom of the tank and my device.
i need to help the air flow just a fraction, it would need to be half the thickness of a credit card.
i im using the istick 50 with innokin t18 tanks, the tank tightens down and the tank air flow vent doesnt line up with the istick air vent.
i dont need to line them up just create a slight gap.
ive tried it with folded and cut paper but its fiddly putting the tank back on each time.
any tips please.

Would either of these help?

www.stealthvape.co.uk/index.php?route=mobile_store/product&fspath=82&product_id=302

www.stealthvape.co.uk/index.php?route=mobile_store/product&fspath=82&product_id=504

[ragjoy]

Mar 7, 2016 13:47:39 GMT Roscopecotrain said:

Mar 7, 2016 13:41:44 GMT ragjoy said:

does anyone have any tips for a washer type idea that i can place between the bottom of the tank and my device.
i need to help the air flow just a fraction, it would need to be half the thickness of a credit card.
i im using the istick 50 with innokin t18 tanks, the tank tightens down and the tank air flow vent doesnt line up with the istick air vent.
i dont need to line them up just create a slight gap.
ive tried it with folded and cut paper but its fiddly putting the tank back on each time.
any tips please.

Would either of these help?

www.stealthvape.co.uk/index.php?route=mobile_store/product&fspath=82&product_id=302

www.stealthvape.co.uk/index.php?route=mobile_store/product&fspath=82&product_id=504

Thanks but They wouldn't really help as I'm trying too create a gap rather than close a gap.
Tightening mine down with minimal pressure is to tight restricting the air flow.

[Ron]

Can you not cut a slight gap make it horseshoe shape?

[Roscopecotrain]

Mar 7, 2016 14:09:57 GMT ragjoy said:

Mar 7, 2016 13:47:39 GMT Roscopecotrain said:

Would either of these help?

www.stealthvape.co.uk/index.php?route=mobile_store/product&fspath=82&product_id=302

www.stealthvape.co.uk/index.php?route=mobile_store/product&fspath=82&product_id=504

Thanks but They wouldn't really help as I'm trying too create a gap rather than close a gap.
Tightening mine down with minimal pressure is to tight restricting the air flow.

What about just putting an o ring from a drip tip over the 510 threading on the tank?

[ragjoy]

Mar 7, 2016 14:17:44 GMT Roscopecotrain said:

Mar 7, 2016 14:09:57 GMT ragjoy said:

Thanks but They wouldn't really help as I'm trying too create a gap rather than close a gap.
Tightening mine down with minimal pressure is to tight restricting the air flow.

What about just putting an o ring from a drip tip over the 510 threading on the tank?

That would do it I think if I can find one thin enough.
I made one from a store card but it was to thick so the Atty wasn't touching the floating pin, I'm sure I'll find an O-ring that will work.
The setup is working mirror less fine it just needs a fraction more air.
Thanks for the help.

[joeten]

Would this place be any help simplybearings.co.uk/shop/index.php?cPath=4501_4705

Found here www.google.co.uk/search?q=1+mm+oring+uk&ie=utf-8&oe=utf-8&gws_rd=cr&ei=tJjdVqqANMGB6AT825bACQ just in case there is a better place you can check for.

[tsoko]

I use heatshrink on all my atties. I am sure that will do the trick, plus they do not scratch your mods.

Something like this www.tlc-direct.co.uk/Main_Index/Cable_Accessories_Index/Sleeving_2/index.html