Is it just me or is the kylin ...

[JayJ]

A bit pants ? Yes it Vapes nice when you've set it up properly but it's the juice flow control that's niggling me. I'm not getting any leaks but it seems to open the juice flow you basically have to tighten the whole top section until you can see your wicks and along my vaping journey if there's one thing I've learnt it's don't overtighten tanks etc., it does not seem to have a part to turn solely for juice flow or am I missing something major here as it's very stiff ? It's the little things like this that will put me off a brand altogether because if that's how it's done why couldn't they have put a bit more thought into it.

Jay

[Perpetua]

striker42 . . . . is our resident Kylin expert IIRC JayJ!

[JayJ]

It must be me then. Unless I've got an iffy kylin then I don't rate the design at all. I can see this landing at the bottom of the garden.

Jay

[striker42]

JayJ, have no fear chief, you ain't the only sailor on the ship. I'll just leave this here allaboute-cigarettes.proboards.com/thread/68207/cure-leaking-kylin

[JayJ]

Sept 16, 2017 18:16:23 GMT striker42 said:

JayJ, have no fear chief, you ain't the only sailor on the ship. I'll just leave this here allaboute-cigarettes.proboards.com/thread/68207/cure-leaking-kylin

Not leaked a drop, that's not my problem. My problem is to open the juice flow it seems you have to tighten and loosen the whole top part of the tank rather than have a part purely to open juice flow. Mines ridiculously tight so obviously takes more tightening to open, resulting in it being almost impossible to remove the tank from the mod it's attached to. I hope that makes sense. Glaringly obvious design flaw in my opinion. Maybe I'm unlucky and got a duffer.

Jay.

[striker42]

Sept 16, 2017 18:42:49 GMT JayJ said:

Sept 16, 2017 18:16:23 GMT striker42 said:

JayJ , have no fear chief, you ain't the only sailor on the ship. I'll just leave this here allaboute-cigarettes.proboards.com/thread/68207/cure-leaking-kylin

Not leaked a drop, that's not my problem. My problem is to open the juice flow it seems you have to tighten and loosen the whole top part of the tank rather than have a part purely to open juice flow. Mines ridiculously tight so obviously takes more tightening to open, resulting in it being almost impossible to remove the tank from the mod it's attached to. I hope that makes sense. Glaringly obvious design flaw in my opinion. Maybe I'm unlucky and got a duffer.

Jay.

Yep, had the same shit with mine but the leaking just put me over the edge. That was the 3rd deck and still it leaked. Glad to be rid of it.

[JayJ]

striker42 and yet everyone raves about them. I can't remember the American blonde girl that does reviews she normally does give aways but couldn't do one on her kylin for the very same thing if memory serves me right. it's all cleaned anyway and going up for trade in an fb group.

Jay

[blakey]

I have 3 kylins and they're all issue free

I must have been lucky going by the problems I've read.
The only reason mine don't get much use is cos the reload is a superior vape.
Jay, the juice flow on my lot do spin 180 without issue, it needs to be on the mod and you need to hold the upper gnurling on the base. Give that a try mate.

[JayJ]

Sept 18, 2017 14:56:59 GMT blakey said:

I have 3 kylins and they're all issue free

I must have been lucky going by the problems I've read.
The only reason mine don't get much use is cos the reload is a superior vape.
Jay, the juice flow on my lot do spin 180 without issue, it needs to be on the mod and you need to hold the upper gnurling on the base. Give that a try mate.

I've done that and it's really very stiff so in rotating it I'm just tightening the tank silly tight to my mod. And when I say stiff I'm talking hurt your thumb and finger tips stiff.

[kevin]

I had the same trouble at first - the trick is, when putting the tank back together to carefully hold the top and bottom gnurled sections and don't touch the glass.

Tighten till it just grips, and then the same again when attaching to your mod. The glass should spin freely, and as long as you're not one of those that gives the tank a turn to make sure it's tight every time you pick it up you should be OK.