New RBA for SXK Billet box...

[aaront903]

Usb is dna 60 only atm as i beleive

[Greigster]

Jun 19, 2018 10:54:28 GMT aaront903 said:

Usb is dna 60 only atm as i beleive

Thanks aaront903 Is that the SXK DNA 60.....

Neil

[aaront903]

Yeah sxk dna 60 mate

[aaront903]

Yeah sxk dna 60 mate genuine board so i beleive though

[Perpetua]

Jun 19, 2018 10:49:05 GMT Greigster said:

Is this an SXK version of the BB with the USB and if so, does anyone have a link please.

Neil

There's the green available at Provapes Greigster:

www.provapes.com/collections/evolv-dna/products/sxk-billet-box-v4-style-dna60-green?variant=43573590979

Pre-order on Fasttech - price is reduced a little with their MAP code:

www.fasttech.com/search?usb%20billet%20box

[aaront903]

I caved and ordered the new billet box and vape shell from 3fvape the other night,shipped this morning,been struggling to enjoy vaping and i regret selling my billet as it was all i needed,so hopefully i will get back to enjoying it again

[Perpetua]

Tempting . . . . . www.3fvape.com/vv-vw-mod/23764-sxk-bb-style-60w-all-in-one-box-mod-kit-w-usb-port-blue-aluminum-alloy-1-x-18650-evolv-dna-60.html#.Wykc94onaM8

[decoy]

www.fasttech.com/products/9653367
bb with dna 60 and usb for escribe only i dont think it will charge the batt
ordered yesterday and even though it says its in stock it changed in my orders to expected in 2 days which is a bit naughty if you ask me
got the vape shell at the same time and it seems im going to be finding something to make the air hole smaller
if your worried about the supplied ones moving about apparently if you give them a little squeeze with side cuts it makes the tube ovel so it grips the sides


edit found these

www.atmizoo.com/shop/vapeshell-mtl-air-flow-pins-kit/
prob cost more than the clone by the time you have paid postage aswell but they are out there

[pyr0]

I found airflow restrictors from a kayfun 5 fitted inside the largest restrictor from the vapeshell

[decoy]

well got the usb bb and vapeshell delivered today and its not as big as i thoght it was
done one build on the vapeshell and it seems to be working rather well but i need to tighten up the airflow a little to get a tight mtl
the side pannels were covered in icky stuffs but it came off with soapy water
all in i liles it

[decoy]

wee update
thought idd killed it with ecribe (not the best idea to mess up a service pack install)but ive got it back running
the vapeshell started gurgling a wee bit so ive redone it with more cotton and put it together the clicky way round to see if that helps
it dont seem to sit square no matter what way round you put it together but it sits flat if that makes sense
i found a smallish o'ring in with all the spares i got with them both that fits round the bottom of the coil over the air holes that give a nice pull the air flow cont supplied is useless
the tank setup is a bit of a new one for me,can i get a 2nd tank ,put the kanger rba in and carry it full or is that a bad idea
to anybody thats not sure on the odd fire button placement for me it just seems to work be it forefinger or thumb

[phtumshk]

Jun 27, 2018 23:32:54 GMT decoy said:

wee update
thought idd killed it with ecribe (not the best idea to mess up a service pack install)but ive got it back running
the vapeshell started gurgling a wee bit so ive redone it with more cotton and put it together the clicky way round to see if that helps
it dont seem to sit square no matter what way round you put it together but it sits flat if that makes sense
i found a smallish o'ring in with all the spares i got with them both that fits round the bottom of the coil over the air holes that give a nice pull the air flow cont supplied is useless
the tank setup is a bit of a new one for me,can i get a 2nd tank ,put the kanger rba in and carry it full or is that a bad idea
to anybody thats not sure on the odd fire button placement for me it just seems to work be it forefinger or thumb

i bought my shell with a new tank and it sat square as you like but the seal was shit on the new tank so i put it in an old 1.

it now sits with the 2 halves out of allignment so the conclusion is its the tanks holes that are out of alignment rather than the rba.

[decoy]

Jun 28, 2018 3:04:10 GMT phtumshk said:

Jun 27, 2018 23:32:54 GMT decoy said:

wee update
thought idd killed it with ecribe (not the best idea to mess up a service pack install)but ive got it back running
the vapeshell started gurgling a wee bit so ive redone it with more cotton and put it together the clicky way round to see if that helps
it dont seem to sit square no matter what way round you put it together but it sits flat if that makes sense
i found a smallish o'ring in with all the spares i got with them both that fits round the bottom of the coil over the air holes that give a nice pull the air flow cont supplied is useless
the tank setup is a bit of a new one for me,can i get a 2nd tank ,put the kanger rba in and carry it full or is that a bad idea
to anybody thats not sure on the odd fire button placement for me it just seems to work be it forefinger or thumb

i bought my shell with a new tank and it sat square as you like but the seal was shit on the new tank so i put it in an old 1.

it now sits with the 2 halves out of allignment so the conclusion is its the tanks holes that are out of alignment rather than the rba.

it dont match up outside the tank but its the no logo ft ver
it still sits flush between the 2 halfs but the top and bottom are a little squiffy (the outside machining is a bit off)
the air restrictors seem to have a bit of resistance when fitting so no flapping about
im not complaining about it as it seems to work rather well and no leaks as yet,considering ive only done 2 builds on it for me thats ruddy good lol
im now on my 2nd day of bb ownership and wondering why i waited this long to get one lol

[decoy]

found that the rubber seal that holds the isub coils together is perfick fit for the bottom of the vape shell
cut a small hole in it and yay nice tight mtl

[phtumshk]

Just seen this on 3fV

Rounded chamber looks like it may be flavour central.

Cant find any info on air flow adjustment but gonna take a punt on 1.