sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Jul 26, 2015 15:01:41 GMT
|
|
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Jul 20, 2015 10:19:03 GMT
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Jun 29, 2015 19:46:45 GMT
Looks lovely. I only really work with 18650's though. I'm guessing that is way too big a battery for a pipe? There are e-pipes that take 18650, but they are specifically made for that. And there are those that are VV/VW, too. I do mainly conversions are there are very few ex-tobacco pipes that will take an 18650. An 18500 is the largest I have managed. |
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Jun 29, 2015 16:29:22 GMT
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Jun 29, 2015 15:10:20 GMT
Meerschaum (as you probably know) is like a soft stone and can be brittle if worked to hard. So, hand tools only - like a Dremel, slowly, with small sanding drums, shaping bits, etc. like these  and these  |
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Jun 29, 2015 13:55:34 GMT
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Feb 24, 2015 22:10:01 GMT
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Feb 8, 2015 21:50:13 GMT
Sorry, I have not been in here for a while.
The Kamry K1000 pipe is OK, so long as you are aware of it's weak points.
1. If you get the kit, bin the charger and get a proper one.
2. The 510 centre pin insulation is weak. If you overtighten any atty it will destroy it and you will get a short. This will cause the spring inside the bottom of the bowl to collapse. That's a safety feature - it acts as a mechanical fuse.
3. The supplied tank atty is not very good.
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Nov 26, 2014 13:40:50 GMT
That must have been a post from a very long time ago. I have to say, I did not care much for the Welsh Pipe. I bought mine ready mixed.
But, you know what it's like with juices - what one person dislikes another will rave over.
With a concentrate, I would say start at 10% and adjust as necessary. Let it steep a while, also.
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Nov 23, 2014 15:52:42 GMT
Just goes to show that, in many cases. CE means "Chinese Engineered" !!
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Nov 18, 2014 20:18:26 GMT
Its an issue mainly if you are using low ohms coils. For instance, mine won't fire at all on a dual coil set-up at 0.8 Ohms. It sees that as a "fault".
The answer is to use higher resistance coils ?
People seem to forget that not so long ago and average/standard coil was considered to be about 2.8 ohms.
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Nov 18, 2014 19:36:53 GMT
Whether you are reading the output in RMS or Average does not make any difference to what its delivering to the atty - only the way you are reading it.
It still uses the same PWM waveform and cycle time/frequency.
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
iStick
Nov 18, 2014 17:23:28 GMT
Post by sej016 on Nov 18, 2014 17:23:28 GMT
I succumbed and got one. Nice piece of kit !
|
|
sej016
Mod Maker
Mainly E-Pipe Mods.
Joined:June 2012
Posts: 489
Location:
Likes: 703
Recent Posts
Last Online May 20, 2018 19:19:42 GMT
|
Post by sej016 on Nov 18, 2014 16:07:45 GMT
OK. I got one. And I am mightily impressed by this little device.  |
|
