bones3
Senior Member
Joined:December 2012
Posts: 416 
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 31, 2013 16:02:02 GMT
i think mine must be over wickin as i have 3x3 goin over the top!!
the coil is running at 2.3ohm(so says the vamo) as i used 0.18 wire
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 31, 2013 14:39:57 GMT
i still gurglin!!
but it could be that the 3x3mm wick thats across the top is to thick and is getting caught under the juice control gap as its only gurglin when its been stood for a while now!!
i will crack it eventually!!
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 31, 2013 13:29:56 GMT
its lookin lovely on the roller  |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 31, 2013 13:29:02 GMT
got the old choddy rebuild used the z for the neg wire and the 3 wick but found it a very tight fit in the ceramic thanks blakey blakey did you use 2mm wick for any of your wicks?? i used your measurements and only managed a 4/3 coil?? |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 31, 2013 11:51:01 GMT
just checked steve it was the ggts base sorry novice mistake  |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 31, 2013 11:41:40 GMT
i found the exploded veiw on the gg wiki thing when i was looking for the mouth piece oring size
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 31, 2013 11:36:08 GMT
morning all
i have read up blakeys how to so im full equiped to hopefully sort my probs out!!
blakey
one question
on lookink at the exploded view of the oddy v1 i noticed a second 9x2 o ring on the vapour tube but actually in the tank above the juice control cap
whats the purpose of this?? any ideas?? is it just a buffer if you open the juice control fully??
i ask this cos my german clone doesnt have it is it needed??
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 30, 2013 22:19:04 GMT
no wonder i coulnt find the guide it was on page 25 not 26  its late!! |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 30, 2013 22:17:18 GMT
thanks all for your input its gave me alot to think about
i see i am going to have to read all this thread but its a bit late now its past my bed time and have hospital app in morn
take care all
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 30, 2013 22:04:40 GMT
Blakey always recommends doing that Z shaped thing with one of the wires Bones to avoid leaking, rather than trapping it . . . you're filling it up with the juice control closed? yes juice control shut when filled just off to read page 26 |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 30, 2013 22:01:56 GMT
im using 3mm with an extra wick across the top both wrapped with the coil i think it would be a struggle to get any thicker to seat properly in the ceramic channels i might be wrong on that just my observation in regards to the bottom o ring when i have cleared gurgle away and left the atty sat with the juice control shut for a while its still clear wouid that not suggest that the oring is seated ok?? i might be wrong on this too |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 30, 2013 21:52:32 GMT
there is a cobra up in the pit if you want a look??
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 30, 2013 21:48:50 GMT
oops double post |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 30, 2013 21:48:15 GMT
got my nautilus/terminator or goddy(German ODDY) as i call it set up and running today but i have a slight prob it vapes well but it floods!! if i close the juice control, blow out or vape till ok as soon as i even crack the juice control open within 30 secs its back to gurgling again its like there is a slight over pressure in the tank causing to much juice to come through any thoughts on the matter any one?? any help would be appreciated as i am a novice with these things as a have used solely gennies for the last 10 months!! so i'm back on the learning curve yet again!! |
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 29, 2013 11:49:09 GMT
thanks for the info steve do you know why the oddy has a second 9 x 2 o ring on the mouth piece but under the the tank cap?? My cheap one came like that. Can you post a picture of your ody and we should be able to tell you which version you have. The cheap ones will not fit an o-ring in the top cap. I just about managed to force an o-ring from an old driptip into the gap. do the cheaper ones suffer from flooding ?? as the air will be sucked in through the gap around the mouth piece and up the wick channels drawing juice with it?? i have one of these coming of a coop of an american forum i thought it was a nautilus when i signed up and paid!! >  > |
|
>