bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 28, 2016 7:33:09 GMT
crin766i have a cyan mini vtc with 2 (ithink) black silicone skins £23.60 posted if ya want it, only been used for about an hour tops boxed or xcube 2 black, boxed ,not used at all £33.60 pm if interested and i will sort pics out
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 15, 2016 19:23:41 GMT
2nd lot gone to @broadblaster
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 15, 2016 19:08:11 GMT
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 15, 2016 18:53:22 GMT
i have 2 lots of drip tips going for little more than postage i split what i had in 2 so they should be pretty much the same each lot has appox. 40 dtips in(approx) ,all come from Fasttech would like £5 each, which includes postage ,paypal family and friends please reply by PM 1st come first served basis
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 2, 2016 23:39:17 GMT
I get it off eBay I brought 5 litres last time
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 2, 2016 19:04:37 GMT
i always wash switch parts and connector parts in iso alcohol to after cleaning to remove any grease (left by my fingers) before rebuilding
but i dont go for clouds just a tasty vape and faultless performance
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 2, 2016 15:56:12 GMT
I'm not sure PerpetuaGis a shout if you any gg tanks left over
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on May 1, 2016 19:33:00 GMT
most of my daily stuff is GG as they are no nonsense devices especially the mods ,yes they might need a good clean every month but then they work as new the older attys take some getting used to ,to get them to work properly but the stainless steel ready wires have made life a lot easier i have 2 penny v2s and 3 penny v3s and they are reliable as are all the newer attys from the GG stable good stuff for all who have never tried GG stuff get a piece and learn the learning curve and you will have something that will stand you in good stead for years and years spare parts are always availiable too i have a UFS (which was made many years ago) and all parts are still availiable to buy
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Mar 9, 2016 14:54:17 GMT
never dry burn my coils i havent in a long time , the chance of breathing in oxide particles ,however small
i just check them for shorts with a Multi meter after building
when the juice starts to colour up when atty is in use i just take it off and stick a fresh atty on and put the old one for cleaning
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Mar 9, 2016 8:20:40 GMT
naDielyes you can use ss wire for normal coils , i have been doing so for atleast 2 years now Ftech do a great range of NR-R-NR SS wires or you and get just SS wire from quite a few places now it is lower resistance than normal Kanthal or Nichrome so you can use more and make longer coils so more coverage i used to use 0.25,0.3 and 0.35mm and i never went above 0.5-0.8 ohm and always spaced my coils hope this helps
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Feb 11, 2016 20:50:07 GMT
I think it just a disclaimer to protect them selves as they use a proper battery tag welder so they should be fine to use unless some one on here knows any different??
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Feb 11, 2016 20:22:11 GMT
Ecolux on eBay tag battery s
And sell all of the good ones tagged
They do state not for ecig use tho
So you takes your chance
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Feb 9, 2016 3:23:04 GMT
I have ordered 8 and 10 from FTech and gear best with no problems
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Jan 22, 2016 23:49:38 GMT
Mine haven't shown up yet¡!?!?
|
|
bones3
Senior Member
Joined:December 2012
Posts: 416
Location:
Likes: 164
Recent Posts
Last Online Mar 22, 2020 1:49:08 GMT
|
Post by bones3 on Dec 9, 2015 9:27:15 GMT
would not be surprised at all nanotm if they dont would be a typical Gearbest ploy!! one of the reasons it was my very last GBest order
|
|