Recent Posts

Yeah. They are straightforward. They just need a proper connection

We got in contact via email, but I can't (and don't want to) stop the discussion.

The problem was that the anodising covers more than needed. What we'll do?
 - we'll clarify the specification for the anodosing company
 - we'll test each MicroStick before the shipping
Currently we test several out of the batch.

This exact problem is reproduced only if the conenctor is fully screwed in. Unscrew it half a turn and the MicroStick will fire. That's why we haven't noticed this in time. My apologizes to all who had to spend time solving the problem.

We fixed one of the MicroSticks with the same problem.

Problem: no contact between external part of 510 connector and the MicroStick's body
To check:
- Press the button and manually connect the atty body and the pressed button with a wire (watch your fingers). If it fires now, the problem is in the contact between 510 connector and the MicroStick body.
Solution:
- Remove the bottom cap. Take out the 510 connector (you can use GP fork for this) and check the threads. They should be clean. Disassemble the connector. Take out the brass pin. Clean all of this. Asssemble and screw in the connector.

Now it should be working. If it doesn't help, first of all check if the external wire still helps.

Ok. We'll bring it to life

Sorry, the thread us so long... Can't read it all.
The first thing you can do to get support is to write us 
mini-ecig.com/contact

FAQ is here:

mini-ecig.com/faq

Currently we have 4 new MicroSticks, which are not firing. All 4 were reported yesterday, so we haven't identified if all have the same problem or different and what actually is the problem.
The most suspected is #3 below.

Here is the summary of all know problems.

---

The connection consists of several parts:
- Minus: battery - button - brass insertion - MicroStick's body - external part of 510 conenctor - atty body - wire
- Plus: battery - brass conductor - brass pin in 510 connector - atty central post - wire

There are several possible root causes:
1) the battery is flat
Solutions:
- charge or replace

2) the battery is too short
To check:
- Press on the button. It shouldn't go all the way down to the body. There should be a gap between the pressed button and the body. It means that it touches the battery.
Solutions:
- slightly unscrew the screw in the button
- use 18500 batteries; all 18500 batteries should be ok
- try another 18490 battery; some of them are really short
- add a magnet

3) no contact between external part of 510 connector and the MicroStick's body
To check:
- Press the button and manually connect the atty body and the pressed button. If it fires now, the problem is in the contact between 510 connector and the MicroStick body.
Solution:
- Remove the bottom cap. Take out the 510 connector (you can use GP fork for this) and check the threads. They should be clean. Screw in the connector and check again.

4) the 510 connector pin has no connection to the conductor inside bottom cap or the extender
Solutions:
- Check if the bottom cap is loose. If needed, slightly screw in the screws in the bottom cap.
- Take off the atty. Press on the brass 510 connector pin inside the MicroStick. Press just once with a screwdriver, for example.

5) atty makes no connection with 510 connector
Solutions:
- if the atty pin is sunk
Take a closer look at the atty (choose any). There is a brass pin in the connector surrounded by the insulator. The brass pin must be higher than the insulator (if you have the atty up side down while looking at it). The MicroStick has the brass pin 3.5 mm in diameter. If the pin in the atty is sunk into the insulator, the atty might work well with many other mods but not with the MicroStick, because in the MicroStick the pin in the atty doesn't touch the 510 connector pin. If possible, disassemble the atty and push out the pin or try another atty.
- if the threads are slightly mismatching
Check if the atty is fully screwed in. Try to apply slightly more force while screwing it in.

Hi all,

The first run is over and now we are ready to annonce
the second run for MicroStick and MiniGen SS!

In short:

• MicroStick is a small mechanical mod for stealth vaping. It can be used with many atomizers in addition to the MiniGen, since all 16 mm atties are ok. For example, use it can be used with Sturm G-Tank, Hellfire, Spheroid, Kayfun mini, Nahual.
• MiniGen is a small genesis tank.

We got loads of positive feedbacks for the quality of the MicroStick and the MiniGen SS.
Both were reviewed by The Hill Giant:

MiniGen:
Minigen by Chels Review - YouTube

MicroStick:
Microstick by Chels Review - YouTube

And here are several words from the owners of the MicroSticks:

“That coating is apparently the same as on the Israeli Tavor TAR-21 assault rifle, I also don't know what it is but it is supposed to be extremely hardwearing and difficult to scratch, **** knows but mine has been thrown into pockets with keys etc and there isn't a mark on it. There's nothing about this little mod that makes you want to wrap it up in cotton wool, perfect little pocket mod and it's built like a tank,very solid..
I use mine the other way round in my fist, firing it with my index finger rather than thumb as the button is not fussy at all, you only need to hit it on the edge and the mod fires perfectly.“ // Maz

“...you can hold it nicely in your fist for a proper stealth vape. I'm so bored of generic 22mm tube mods and this is an absolute triumph in all aspects” // Chasey

“It's so small but feels really solid.” // bennyboy

“-The button action is very smooth ..., you don't have to worry about hitting it dead center. ...
- It hits hard. Getting great results with the Nahual as well as my G-Tank with the brass pin upgrade.
- Since the button is on top, I don't have to worry about locking it when placing it down, and compared to lengthy tube mods, I like how you can just plop it down and not have to worry about the thing tipping over.“ // MoarVapour

“its a fantastic little mod, well thought out and well executed.
pretty much the perfect stealth vaping device
colour me impressed…” // baron von bubba

In the store you can see that the promised shipping date is December, 15. This is our deadline for the shippings. It includes some risk time, because we don't want to be late anymore. In fact, we hope that Chels will finish the second run earlier.

The pre-orders will be opened for about a week, so...

Welcome to the store!
Mini ECIG